MacBook Pro 13 "Unibody Mid 2009 Reemplazo de la tarjeta AirPort

Escrito Por: Andrew Bookholt
  • Comentarios: 51
MacBook Pro 13 "Unibody Mid 2009 Reemplazo de la tarjeta AirPort

Dificultad

Difícil

Pasos

24

Tiempo Requerido

2 horas

Introducción

Utilizar esta guía para reemplazar una tarjeta AirPort muerta para recuperar la conectividad Wifi.

  1. dOyroxuUBfNu1T4K

    • Retira los siguientes 10 tornillos que sujetan la tapa inferior del MacBook Pro 13 "Unibody:

    • Siete tornillos Phillips de 3 mm.

    • Tres tornillos Phillips de 13,5 mm.

    Compare the short screws carefully before reinstalling them. The shouldered screws go in the holes on the front edge.

    David Kilbridge -

    Before I started removing any screws I took a piece of paper and drew the bottom of the laptop and put a piece of double-sided tape in the spot where each screw goes. That way when I took out the screws, I could put them on the tape so I knew exactly which screw went in which spot. I did the same thing for dismantling the inside on another sheet of paper, then a third sheet for the screen after getting the front glass off.

    mastover -

    I use a similar technique: I print out the iFixit manual for the job, and Scotch-tape down the screws/brackets/cables I remove at each step next to the component descriptions. That way, when I'm reassembling, the bits are taped right next to the photo of where they came from.

    adlerpe -

    That's exactly what I do for all my repairs! It's the best way to keep track of all of the parts ' original location and to make sure that you don't miss any parts during reassembly.

    joyitsjennie -

    Great idea and one I use often

    Thomas Overstreet -

    Excellent idea! Thanks for sharing it here.

    Laura Sharkey -

    I used a 00 that fit but the screws were very tight so I used a tiny paintbrush with some wd40 on it and put it around the edges of the screws. Worked like a charm

    valentinedhdh -

    I use a magnetic mat and place the screws in order on that :)

    Cary B -

  2. bLtKOLyJdyAxkZaG

    • Levanta ligeramente la tapa inferior y empuja hacia la parte posterior para liberarlo de las pestañas que lo sujetan

    In the introduction you should link fixers to this excellent doc: https://www.ifixit.com/Misc/HD_Software_...

    It is really critical, super easy, and free(!) to clone your existing drive onto the new one you will install. I ran into one error, but SuperDuper! support replied immediately on how to fix it...Thanks ifixit and SuperDuper! (I ponied up the $28 for the software anyway, I was so impressed!)

    Mike -

    Long story short: I drank the AppleKoolAid back in 1984 and have always left the guts of my machines up to Apple - until recently when I needed to swap the SATAs from my original MacDaddy (2009 13" MBPro that I killed in 2018 - coffee + blackout = OOOOPS) into a pristine 2009 MBPro from a Goodwill in North Carolina through eBay. I need the files from iCal and MacMail that can't be opened in my newer machines.

    Well . . . I ain't never done nuttin' like that, before!

    Enter Luke Miani on YouTube. He raves about you guys! So, I watched everything I could, read your site, bought the right tools and at the ripe old age of 72, I sat down, this morning and did the work. Now my original MacDaddy lives in MacDaddy2.0.

    Am I allowed to cry?

    Seriously, I can't thank you enough for your bitchen site and killer tools. I wish I'd'a been turned on to this shizzle 30+ years ago.

    IFIXIT - IDIGIT!

    kath myers -

    HAHAHAHAHAHAHAHAHAHA.

    That was a brilliant read.

    Yes, I came across ifixit a few years ago. Totally helped me out on several occasions.

    Glad your Mac repair journey worked out.

    :)

    Cary B -

  3. B1SUXfcr5fruMavs

    • Por razones de precaución, le recomendamos que desconecte el conector de la batería de la placa lógica para evitar cualquier descarga eléctrica.

    • Utilice el extremo plano de un spudger para levantar el conector de la batería hacia arriba fuera de su toma en la placa lógica.

    Cita de gansodesoya:

    why is step 3 necessary?

    Just to disconnect any power source to avoid damages by short-circuits.

    MrKane -

    How do you get that battery connector back on? Do you just press it in back in place after you're done?

    Horace Chung -

    yes. I usually plug it in before I screw it down so I can lift the battery a bit and have enough slack to be able to go straight down on the connector, otherwise it comes in on a bit of an angle, which can't be good (though not necessarily bad).

    maccentric -

    This step almost finished me, and I did extensive damage to the battery plug. Fortunately, I later replaced the battery, and the replacement came with a new plug! :) Newbies need to know - 1. The battery plug is like a thin lip on a thicker lip, so you need to pry BETWEEN 2 thin lips to get it off, else you are trying to yank out the socket. 2. Mine was initially VERY tight, and trying to get it out broke the plastic on all sides of plug, even though I was as careful as possible. Luckily, this didn't hurt functionality and I later replaced the battery. AFTER disconnecting once, it was never so tight again,

    Jeff Diamond -

  4. aCHD62J31BaNKjt1
    aCHD62J31BaNKjt1
    pCPfK5moiENgSeGJ
    3aArQDlKLo1KZhmW

    • Utilice el extremo plano de un spudger para mover el subwoofer / conector del cable del altavoz derecho hacia arriba fuera de su zócalo en la placa lógica.

    • Tenga mucho cuidado de presionar debajo del conector como se muestra, y no debajo del enchufe en sí. De lo contrario, puede separar accidentalmente el zócalo de la placa lógica.

    Please Be Carefully With This Step, Because I Had To Resolder It Back To The Logic Board. But There Is A Black Foam Piece Over The Cable You Have To Pry Up, Lift The Foam Piece And Then Try To CAREFULLY Pry Cable Connector

    BWilliams842 -

  5. uCAOWLYpZGiekrxH
    uCAOWLYpZGiekrxH
    wbVS1cJLaQLTTvG4

    • Desconecta el cable de la cámara deslizándolo horizontalmente fuera de su zócalo.

    • Tira del cable paralelo a la superficie de la placa lógica, en la dirección de la unidad óptica. No tires hacia arriba o destruirás el conector.

    • Si ves un pequeño retenedor de plástico adherido a la placa lógica que evita que el cable de la cámara se deslice, quítalo con cuidado de la placa lógica. Aplica un poco de calor con un secador de pelo o una pistola de aire caliente si es necesario para ayudar a suavizar el adhesivo que lo mantiene en su lugar.

    • No intentes desconectar a la fuerza el cable con el retenedor en su lugar.

    • Si aún tiense problemas, usa la punta de un spudger para empujar cada lado del conector y "camina" lentamente para sacarlo de su zócalo.

    Be careful to the piece of plastic that prevents camera cable failing out its socket! Do not force connector! Look at plastic before attempting to remove connector Plastic is partially covered by cdrom flat connector at right of camera cable connector

    Silvio -

    This step is unnecessarily tricky. I’ve tried to make it better by adding images highlighting the plastic stopper thingy and showing a clear arrow of the direction the cable should be pulled.

    However, simply pulling the cable may not be enough to remove it. It sure wasn’t for me. I think there ought to be a close-up of the two little nubbins on the sides of the plug which one uses to wiggle it loose from the connector by gently prying with a tiny flathead screwdriver. I didn’t add that tip because (a) it would have made the instructions longer, (b) I didn’t think to take a photo of it, and (c) using a screwdriver carelessly next to the logic board could scratch or break components on the motherboard. A guitar pick or very small spudger might work.

    hackerb9 -

    @hackerb9 Thanks for your edits and comments! I took some additional shots and tried to clean this up a little for everyone. There should be a lot less confusion now. Interestingly, neither of the two MacBook Pros used for these guides had the plastic retainer piece you folks mentioned, but I left that image in a link so everyone can still see what it looks like if needed.

    Jeff Suovanen -

    Thanks for incorporating some of my edits and for taking new photos.

    Are you the one who took the original photographs? If so, you did originally have the hard plastic retainer as it was in those photos, just obscured by your thumbnail. The glue on the retainer allows it to shift a bit, so it's possible you took out the cable and knocked off the retainer without noticing it.

    Your two frame animation of pulling out the plug is helpful to show the proper direction. Given the number of people who have destroyed their MacBooks from this procedure, I think we should do even better. The instruction would be clearer if it said, “Disconnect the camera cable by sliding it horizontally out of its socket.”

    Also, if you can post a link to a picture without fingers in the shot, I will add an arrow showing the proper direction. (I would have added it to the original, but visually it would have gone through your fingers.)

    hackerb9 -

    P.s. this isn't as important, but where did you hear the tip about the hairdryer? I'd leave that out as firmly peeling it up works fine.

    hackerb9 -

    Negative, I’m not the original photographer. You’re right, I do see the retainer in some of the previous photos, although it wasn’t in any of the images for this particular step. May have been an oversight on the part of the original author! So I’m glad you caught it. I updated the verbiage as you requested. Don’t worry about adding arrows—at this point, if someone ignores both the images and the multiple warnings in the text, that’s no longer a fault with the guide. The heat/hairdryer tip is standard practice for anything that’s secured with adhesive—I hardly ever work on a MacBook of any vintage without using a heat gun at least a couple times. It may not be strictly necessary, but the result is much cleaner and it reduces the risk of accident.

    Jeff Suovanen -

  6. 2CuX4NnYgJAYMCVV

    • Desvíe el cable de datos de la cámara del canal de la unidad óptica.

  7. NBScWjQ66kyBbwVp
    NBScWjQ66kyBbwVp
    RokUVKGc3ClkqUDp

    • Retire los siguientes tornillos que sujetan el cable de datos de la cámara y el altavoz derecho a la caja superior:

    • Dos tornillos Phillips de 8 mm.

    • Un tornillo Phillips de 4mm.

    • Uno de los tornillos Phillips de 8 mm probablemente permanecerá cautivo en el bucle de tierra del cable de la cámara.

    • Resbala el soporte del cable de la cámara hacia afuera desde debajo del subwoofer y retírelo del la computadora.

  8. OtImO3lYHNGS6wlK
    OtImO3lYHNGS6wlK
    eXZKb3KMdjSMZXRT
    qlV2LWOvHQ6PwgLE

    • Agarre la lengüeta de tracción de plástico asegurada al bloqueo del cable de datos de la pantalla y gírela hacia el lado DC-in del equipo.

    • retire el conector del cable de datos de la pantalla directamente de su toma.

    • Asegúrese de tirar del conector directamente y no hacia arriba de su toma.

    Well, my display ended up looking like this after the repair:

    http://i1106.photobucket.com/albums/h366...

    As you can see, there was a light/dark banded pattern along the bottom of the screen, corresponding to the LCD's backlight. In my case it was also accompanied by a constant high pitched whistling noise. I swear to anything that's holy, it was not coming from the fan or the speaker, but rather the motherboard itself.

    Anyway, both these problems went away when I disconnected and reconnected the connector at this stage. I'm saying this on the off chance it helps someone else.

    Jonty Levine -

    It's not to clear but there is a piece of spring steel that rotates away from the main (circuit board side) of the connector....this piece sort of hugs the parameter of the screen cable locking it to the circuit board...both arms wrapped around your brother....looking closely (10x magnifier) at this cable one of the gold connections is slightly oxidized---my display arbitrarily flickers and this symptom is lessened as the temperature increases...I suspect this is the cuase of the screen flashing on/off

    brian62 -

  9. YHI6vB4wCvg23uBM
    YHI6vB4wCvg23uBM
    ZrRKYGFdYuBPK4XV

    • Quite los dos tornillos siguientes que sujetan el soporte del cable de datos de la pantalla a la caja superior:

    • Un tornillo Phillips de 7 mm.

    • Un tornillo Phillips de 5 mm.

    • Levante el soporte del cable de datos de la pantalla fuera de la caja superior.

  10. w4PaV4Ytic61NKUn
    w4PaV4Ytic61NKUn
    TnsXUEecrjPT54HD

    • Usa tu destornillador Torx para quitar los dos tornillos exteriores de 6,5 mm que sujetan cada uno de los dos soportes de la pantalla a la carcasa superior (4 tornillos en total).

    • Los modelos de mediados de 2009 requieren un destornillador Torx T6, mientras que los modelos de mediados de 2010 requieren un T8.

    Hey folks, regarding the screw/driver sizes: there are separate guides for the Mid 2010 model with the T8 screws. Always use the correct guide for your model to avoid confusion, stripped screws, etc. Hope this helps!

    Jeff Suovanen -

  11. c6INZGJPJQqTlMW6

    • Abra su MacBook para que la pantalla sea perpendicular a la mayúscula.

    • Coloque su MacBook abierto en una mesa como se ilustra.

    • Mientras sujetas la pantalla y la carcasa superior con la mano izquierda, utiliza el destornillador Torx para quitar el tornillo restante de 6,5 mm del soporte inferior de la pantalla.

  12. rOIast44GfWa55h6

    • Asegúrate de sujetar la pantalla y la mayúscula junto con la mano izquierda. Si no lo haces, la pantalla liberada / mayúscula puede caer, dañando potencialmente cada componente.

    • Retira el último tornillo Torx de 6 mm que fija la pantalla en la parte superior.

    Removing the screen assembly this way, with the computer standing on edge, is needlessly risky and difficult. By the 5th or 6th time I did this procedure (of perhaps a hundred), it dawned on me that there’s a way, way easier method for the whole lid removal job: 1. After removing the bottom cover and disconnecting power, hang the open laptop, keyboard down, facing away, over the edge of your work table with the lid assembly hanging down, monitor facing toward the table and pushed against the table edge. (If you’re klutzy, tape the main body to the table so it can’t slide around.) 2. With the unit positioned this way, you can easily disconnect the various cables & remove the 6 hinge screws. Now the lid assembly will just be hanging, easy to lift away from the main body without difficulty or danger. 3. Reverse this to put it back together.

    clinton -

    Nice tip, Clinton! I’ll have to try that next time. Do you have photos of how it is done so this guide can be updated?

    hackerb9 -

  13. ZYiiL2jdwOpXXcvJ
    ZYiiL2jdwOpXXcvJ
    niqZhXDVagv6WANS

    • Coge la parte inferior con la mano derecha y gírala ligeramente hacia la parte superior de la pantalla para que el soporte de la pantalla superior despeje el borde inferior.

    • Gire la pantalla levemente lejos de la parte inferior

  14. ntBnWP6Z11ASxKLP

    • Levante la pantalla hacia arriba y lejos de la parte superior, teniendo en cuenta los soportes o cables que pueden quedar atrapados.

    Re-assembly hint: Laying the base, keyboard down, on a table top with the hinge side over the edge about 1/2" toward you is a more stable position for re-assembly than trying to do this up on its edge. This has the added benefit of being able to reinsert the torn screws vertically.

    Pete H -

    May be in the wrong place but then please direct me. At this step, can I just take off the upper half (meaning the screen, LCD, and top housing shell in one) and simply replace it with another upper half of the same edition???

    cmackay13stmarys -

    Yes, you can. Thanks what I'm doing now. :)

    Mike Mayaka -

  15. wgRoBlTmHppiPiwQ
    wgRoBlTmHppiPiwQ
    HCyfQLHZqYvrKLtF

    • Agarre la cubierta del embrague como se muestra y deslícela hacia el lado derecho de la pantalla.

    • Debería moverse aproximadamente 1/4 "y detenerse. No lo fuerce más allá de este punto.

    i've found this impossible to get back on correctly.

    i cant get the plastic to slide back that 1/4" it needs to fit properly

    Does anyone know any tricks? :(

    Ashley Berthon -

    imagine the monitor upside down and the screen facing away from you. You have to put the cover over to the right of where it goes about an inch or 2 and it will go in, then, slide it left to lock it into place

    stdonato -

    I was replacing a clutch cover that had cracked into a few pieces. I found the replacement didn’t slide to the left on installation. On further investigation I found the tabs from the old one were broken off inside where the cover slides. Once they were removed the install wen much better.

    I found my replacement cover on Amazon.ca in case someone needs a Canadian source.

    Dean Landry -

  16. Vns5bAdNqAak5lWZ
    Vns5bAdNqAak5lWZ
    EFvH5PPgXLgPSsXL

    • Balancee suavemente la cubierta del embrague hacia adelante y hacia atrás en su eje largo mientras lo retira de la pantalla

    • Haga esta acción a lo largo de la longitud de la tapa del embrague hasta que pueda levantarla del marco y conectarla a la pantalla.

  17. iegYVqjNQuaLTiBw

    • Retire la tapa del embrague de la pantalla.

    The flat face goes on the bottom edge of the display. The display and wifi cables must be routed below the hinges in the display, that is, closer to the bottom edge of the display.

    Robert Rossi -

  18. NBXxDAcXUNRiYJ3K
    NBXxDAcXUNRiYJ3K
    PJTRR5mHDQDjOHhD

    • Utilizar la punta de un spudger para sacar los dos conectores de antena AirPort de sus enchufes en la placa AirPort.

    • Tenga cuidado de no romper las tomas de la tabla AirPort.

  19. 5kZXCl5wuU36EvgZ

    • Retire el único tornillo Phillips de 3 mm que fija la tarjeta AirPort a la pantalla más cercana a la antena AirPort.

  20. ZR4a1DOSQDyZUanb

    • Retire el único tornillo Phillips de 3,3 mm que asegurar el retenedor del cable de la cámara a la pantalla.

    this is on the other side, watch the glass of the display below

    Carl Gennheimer -

    Thank you! I thought the photo was looking at the left hand side.

    Andrew Wainwright -

  21. gjYEaE3Gwd1FYfar
    gjYEaE3Gwd1FYfar
    RPIWeFUmqifr4hP3

    • Oriente su pantalla como se muestra y retirar el retenedor de plástico negro de la cámara hacia el lado derecho de la pantalla.

    • Retire el retenedor del cable de la cámara.

    In the second picture for this step the U notches on the wifi connector are facing out when in the socket, and this is quite misleading. Putting them in like this will not work and could potentially cause some serious damage to wifi card or motherboard. Be wary of this guide, and make sure you take pictures of how things are before you touch them.

    acurns1 -

    How do I find out the specifications for the Airport Card? There is none here…

    How do I know if the problem is on the card or the cable?

    Marco -

    Sorprende como reparar mac fácil y rápido

    PC Macintosh -

  22. BfsAQsriSukpXJ5D

    • Con cuidado, tire del conector del cable de la cámara hacia el lado derecho de la pantalla y fuera de su zócalo en la tarjeta AirPort.

    • Al volver a colocar el cable AirPort, asegúrese de que las muescas en forma de U en un lado del extremo del cable no estén visibles (frente a la tarjeta). Si el cable está instalado incorrectamente, causará daño a la placa lógica.

    I fried both of my Airport cards, couldn't figure out why, and came back here and read about these little U-shaped notches. I had to bring the computer into my office to compare both sides of this cable. I would be nice to make sure that this tid bit of information is very noticeable for those who are following along.

    wcking -

    Yea, I fried two motherboards before I came back here and re-read that the U notches must face the airport card.

    wcking -

    A super closeup photo of these notches would very helpful.

    Peter Mayo -

    If the note in this step can be updated to more accurately describe why the notches must be visible, that would be most helpful.

    Perhaps written as per “The camera cable (ie the AirPort cable) whilst it can fit in both ways, you WILL cause damage to either the card, the motherboard or both if the orientation is not correct.

    The cable MUST be installed so that the notches on one side of the cable are not visible”

    Charlie Nancarrow -

    Er, how sure is everyone about the directionality here? In the various images in this tutorial the connector appears with the U notches both facing and away. Perhaps the images reflect the learning process, but maybe the dot on the cable is key? One thing I can confirm is that it does matter - the cable connectivity is not symmetric.

    Robert Rossi -

    Well, I don't yet know what damage I did to my logic board, but the instructions here are correct, at least for the system I am working with: if installed the other way around (with the U notches facing away from the connector), the system will turn on but when you try to shut it off (power button, shutdown option in OS) it will immediately turn back on. Only a long-press on the power button will shut the system down such that it stays off.

    Robert Rossi -

  23. SP5e21JoE6xuTdWT

    • Retire el tornillo Phillips de 3 mm restante que asegura el lado de la tarjeta AirPort más cercano a la bisagra del embrague derecho.

    This photo can be slightly misleading if you're not careful. It appears that unlike my cable, the pictured cable has the gray dot on both sides. In this photo you can see the 2 little sideways U notches that should be on the OTHER side. In photo 22 you can see that there are NO such notches as he is sliding the cable out of the connector.

    My gray dot is only on the underside (not visible when the cable is plugged in correctly. When I first took the cable out to replace my Airport board, I thought maybe it had been inserted the wrong way which will damage the motherboard. So the gray dots are not a good indicator, just look for the sideways U notches as indicated in the iFixit directions.

    madmaxmedia -

  24. t5VGJoTqnRwbwVAL
    t5VGJoTqnRwbwVAL
    fN2Sq6KWkwBtLZ3E

    • Tire de la tarjeta AirPort lejos de su disipador de calor y retírela de la pantalla.

    • Antes de instalar una nueva tarjeta AirPort, asegúrese de que el material térmico en su superficie esté intacto y alineado con el pequeño disipador de calor en el marco de la pantalla.

Conclusión

Para volver a armar su aparato, siga estas instrucciones en orden inverso.

Autor

Andrew Bookholt

578639 Reputación

5 comentarios

I am sick of the occaisonal misinformation iFixit provides. The longer cable that connects on the right side of the screen is so very obviously not just the camera cable. It is also the cable for the Airport and Bluetooth cards... This misinformation led me to spend 100€ on two LCD cables which I now have no use for.

I don't wish to just complain though of course. Can someone please correct this? On the other pages for this MBP the cable is listed in the same way.

spacec0w -

The official Apple name for this cable is "camera cable", so that is what we call it. You'll have to take it up with Apple to change the name, as we try to stay consistent with how they name parts.

Andrew Bookholt -

I think iFixit does an amazing job of being accurate, given that the guides are written based on physical tear-downs. As a small-time mac technician, I am eternally grateful for the unlimited use of free, comprehensive guides. Instead of complaining about free advice, you can easily submit an edit to the guide if it is truly in error. The bottom line with Apple products - they are impeccably engineered, although have some annoyingly tedious steps because of the compact nature. They are build to last, but BE GENTLE!!

Logan Bean -

The connector from the cable into the airport card is socketed in different ways on the pictures in step 21, i have noticed that the connector fits in either way, but what way is the right one? im asking because after i followed this guide my airportcard doesnt work anymore:(

info -

see comment on step 22

Logan Bean -