Reemplazo de cubierta de Mac Mini Mid 2010

Escrito Por: Andrew Bookholt
  • Comentarios: 14
Reemplazo de cubierta de Mac Mini Mid 2010

Dificultad

Moderado

Pasos

7

Tiempo Requerido

No hay estimado

Introducción

Usa esta guía para remover la pequeña cubierta de plástico moldeado usada para dirigir el aire frío hacia el disipador de calor.

  1. EHeE3OSxnGBpG5cR
    EHeE3OSxnGBpG5cR
    nrQsgSGm4FLoIsDn

    • Coloca tus pulgares en los huecos en la cubierta inferior.

    • Rota la cubierta interior en sentido horario hasta que el punto blanco pintado en la cubierta inferior este alineado con el aro grabado en la cubierta exterior.

  2. AK1A1wVNKrIgIRBY

    • Inclina el mini lo suficiente para permitir la cubierta inferior salir de la cubierta exterior.

    • Remueve la cubierta inferior y colócala a un lado.

  3. JhqtrsyiKfY64LhN

    • Remueve los dos tornillos T6 Torx de 11.3 mm que aseguran el ventilador a la tarjeta lógica cerca de la placa de la antena.

    There are actually 3 T6 screws securing the fan. The third screw is out of the screenshot, just below the RAM.

    inferno10 -

    Nope, that third screw is actually just a post that the rubber grommet attached to the fan body slips over. Step 4 shows how the fan comes off of it. When you go to remove the fan, you simply remove the two screws closest to the antenna plate and then lift the fan off this post. The screw you are talking about is removed in Step 14 and does not need to be removed until this point.

    Andrew Bookholt -

    Successful install completed, but I had some trouble getting the fan reinstalled. When I removed the fan from the "Step 14" post, the rubber piece stayed on the post. When attempting to reinstall the fan, it was impossible to get the loop to go back over that rubber piece. So, I had to remove the post (again), and with the help of the spudger and some patience, worked it through. Then installed the fan using the 2 screws and the post. I think it may have saved some time and trouble if I just removed all 3 in the first place, leaving the post in the fan.

    meag -

    On mine I needed to remove the 26 mm T6 Torx standoff during this step rather than step 12

    philipashlock -

    on my mid-2011 mac mini, that 3rd T6 post/screw had to be removed to get the fan out. It goes right through a hole in the fan housing. No way the grommet is slipping over anything without wreaking major havoc.

    Derek Shaw -

    On my mid-2010 mac mini, also removed the 26 mm T6 Torx standoff during this step instead of step 12. Having completed the steps, it appears my hard drive is from mid 2011, so maybe the production line for mine had changed.

    jstraath -

  4. abhjpqhOsxFfJyTB

    • Levanta la oreja del ventilador mas cercana a la RAM hasta el punto muerto fijado a la cubierta exterior.

    • Si el ventilador no se separa del tornillo de separación con una moderada cantidad de fuerza, puede usar un desarmador T6 Torx para simplemente remover el tornillo.

    Pulling on the ear didn't do anything, so I removed the whole screw at this step. The screw stayed fixed on the fan and I didn't have to remove it at the step where you remove the logic board screws.

    Probably I didn't want to use too much force .. but it worked

    Alexander Kogler -

    This is the approach I used. no way was the "ear" pulling over the head of the standoff without breaking something. The standoff simply unscrewed from whatever is under the logic board and stayed with the fan assembly. WAY safe

    Derek Shaw -

    Loosen the fan standoff from the motherboard using a T6 driver.

    bobcloninger -

    When I pulled the fan ear off the standoff the rubber grommet stayed on the standoff. That's fine, but it makes it difficult to put the fan ear back on during reassembly. So I just pulled the rubber grommet off the standoff and put it into the hole in the fan ear. Then I was able to push the fan ear onto the standoff with out trouble during reassembly.

    Dave Hein -

  5. 25C5Ye3RCQIpcttO

    • Levanta el ventilador de la mini para que haya suficiente espacio para acceder a su conector.

    • Con cuidado jala los cables del ventilador hacia arriba para levantar el conector del ventilador de su zócalo en la tarjeta lógica.

    • Remueve el ventilador.

    Be careful here, this is not a simple action. Pulling on the wires risks them coming out of the sockets of the connector that attaches to the pins on the board. I had to use an Xacto knife to push on the end of the connector to push it off the pins rather than pull.

    Brian -

    Actually, just sliding a spudger under the wires and edging upwards is the easiest way to disconnect this connector - and most others, too.

    Aleks Gekht -

  6. 5Hx5hdSKCOfwox3I

    • Remueve el único tornillo T6 Torx de 3.5 mm que asegura la cubierta a el disipador de calor.

    This is a screw into the head of another screw below it that holds the main board. When I took out the fan, the top screw AND the longer 26 mm screw came out together so when I was putting my mini back together I thought for a moment I had lost a screw.

    info -

  7. t3RIVgUYaeuWDM2A

    • Levanta la cubierta de su extremo mas cercano a la placa de la antena.

    • Rota la cubierta lejos de la cubierta exterior y remuévela de la mini.

    This is wrong step. If you need remove this out, it would be better to pull out logic board, and remember to remove cables attached on it before pull out.

    Lin Adison -

Conclusión

Para reensamblar tu dispositivo, sigue las siguientes instrucciones en orden inverso.

Autor

Andrew Bookholt

578639 Reputación

0 comentarios