Reemplazo de la pantalla del iPod Nano de cuarta generación

Paso 1

Inserta el borde de una herramienta de apertura de iPod entre la brecha de la carcasa exterior y el bisel superior.
Has palanca en el bisel superior separándolo del adhesivo asegurandolo al retenedor de la pantalla.
A este punto el deslizado del interruptor de bloqueo es libre y puede que se caiga. Se cuidadoso de no perderlo.

Be sure to use the smaller iPod opening tool and press it in FIRMLY in order to get enough leverage to get under the bezel and pry it off. Adhesive is very strong, so don't be afraid to use a little bit of force.

captcarl13 -

Tool broke before I could get the cover off !!! So I’m done before I even started !!

linda45p - 15/05/19

I have a Apple iPod Nano 4th gen(Green) and I only have 7 tech pieces to the iPod and I may/might have the small philips screws and I am not sure how to fix the iPod nano

Nick Davies - 19/08/19

I also had Problems to remove the bezel. The solution was to start with a very small screw driver from the hole of the switch. There I could lift it a bit and get the plastic tool in between. Than it was easy.

Michal Niewiadomski - 28/08/19

After replacing the battery, the old glue would lump up too thick, and also become too weak to fix the panel back to the outer case. I have scraped all the old glue off using a small flat head screw driver, and affixed a double sided adhesive tape cut into small strips, which was successful in both aspects.

diytradjazz - 23/10/19

TIP: Use a plastic tool and pull it out through the hold switch. This may break the top bezel, but this was the only way to get it off.

Caleb Murphy -

Paso 2

Quitar el botón de bloqueo del iPod Nano

Paso 3

Remueve los dos tornillos Philips angulados de los dos bordes del retenedor de la pantalla.
Las cabezas de estos tornillos son extremadamente pequeños y pueden ser arrancados fácilmente.

Be sure to use a good phillips #00 screwdriver here, or you run the risk of stripping the very small screws.

iTronics Repair -

The screws were covered with the adhesive. They were very difficult to remove.

I RUINED the hold switch! I accidentally broke the cord. 0_o The directions were kind of unclear.

bodieg -

Cita de bodieg:

The screws were covered with the adhesive. They were very difficult to remove.

I RUINED the hold switch! I accidentally broke the cord. 0_o The directions were kind of unclear.

Step 12 is misleading as it does not show to remove the screen from the metal frame.

bodieg -

Sorry guys, but the explanations are really bad. Go onto youtube and watch it. This site misses heaps of steps. I just broke my iPod :(

S Mile -

Like others have noted, screws are covered in adhesive and difficult to remove. Take extreme care to not strip the heads. I'd suggest using a very small flathead to scrape some of the adhesive off before attempting to remove the screws.

captcarl13 -

a 1mm slotted screwdriver will work in a pinch, but be carefull and make sure you get the angle just right

andrew -

The tools list doesn't say you need an iPod opener to, nor does the parts list day you'll need a new click wheel, though this is called ”...click wheel REPLACEMENT”. I don't get the feeling these are very trustworthy instructions, ESPECIALLY after having read other comments. I'd say BEWARE, and look at a variety of resources to get a much more comprehensive picture.

Skyfire - 20/04/17

Actually, the screws are not aligned with the edges of the iPod, which means that you must not try to unscrew them vertically. If you do there is a good chance that you damage the head of the screws. Thus look carefully with a torch to see at what angle you have to unscrew them.

Fabrice Sarelli - 07/12/17

Actually, the screws are not aligned with the edges of the iPod. That means that if you try to unscrew them vertically, there is a good chance that you damage the head of the screws. Thus, look carefully with a torch to see exactly at what angle you need to unscrew them safelly.

Fabrice Sarelli - 07/12/17

Everything was good up to this point. I could barely see the screws and ended up stripping them. Just gave up at this point and threw the

Ipod on the ground and stomped on it.

gonzalo gonzalez - 25/03/18

I agree with several other contributors here, that a properly sized flat screwdriver *that is not worn* held at the correct angle is a better option than a phillips because the screw head is filled in with adhesive tape. BEWARE: The screws on the top and bottom outer edges are not parallel to the case. They are offset by 25 or 30 degrees, with the tips of the screws pointing out towards the outer edge of the case with respect to where the heads are. Use something to get magnification so you can really see how your screwdriver fits, and whether it’s engaged. An undamaged and properly sized standard screwdriver held in the appropriate orientation will readily remove the top and bottom side screws without stripping and with very little force. Feel for engagement — press the screwdriver in just enough to get past the adhesive. Not much torque or pressure is required — just a good fit. You must have the right tools to do this job successfully, and look under high magnification. Align your screwdriver!

Barry L. Kramer - 05/08/18

In accordance with another source, I have bought online and used a Phillips #0000 screw driver, which worked pretty well here. It costed me only $2 .

diytradjazz - 23/10/19

Screws are inserted under an angle. Would suggest to use a jeweler’s magnifying glass to check the angle before sticking any screw driver in there.

aramis -

Paso 4

Introducir la herramienta de apertura del iPod entre la carcasa exterior y el contenedor del display.
Usar la herramienta para deslizar ligeramente el display ensamblado de la carcasa.
No girar el contenedor del display fuera del borde superior del display, ya que está enganchado un fino flex, el cual se puede romper muy facilmente
No mover fuertemente el contenedor del display, el cable del botón de encendido esta unido y se puede romper.

I found I had to gently pry the retainer open with a craft knife (xacto knife?) as the plastic opener tool was too blunt or soft to get any purchase...

aaaidan -

My nano had a "swollen" battery which wedged the LCD between battery and front glass. As a result, this step didn't work, I couldn't pull out the TFT and botched case, TFT and TFT frame until it came out. Telltale sign was a display that looked like there is a water between glass and LCD. The other nanos I've opened didnt have this problem and came out effortlessly, so if yours is stuck, don't feel bad, there's not much you can do!

oliver - 08/04/17

What to do if the upper metal base (which is fixed to the circuit with 2 screws) came off when extracted?

Which side can I anchor to force the display to exit?

Francesco Taliercio - 13/02/20

Paso 5

Deslizar la pantalla fuera del iPod. Se puede mover unas 5" hasta que el cable del display llegue a su limite de tensión.
No poner tensión innecesaria en el fino cable del display.

I have several problems in taking it out. I don't know if it is dued to the glue that the iPod has inside. Could you help me. Thanks

Hector -

instructions say 5" (inches) it really means 5mm

pedalsandpicks -

Cita de pedalsandpicks:

instructions say 5" (inches) it really means 5mm

If you're gonna repair the way you read it will get you nowhere: the text reads .(as point)5 inch. Which is about 12mm.

Frank veenis -

The glass panel can be very difficult to get moving requiring a lot of downward force. I have found good old fashioned spit to be very useful here.Just lick both thumbs and rub on fingers until just sticky enough.

This willl move the glass.

Pete Green -

Paso 6

Con la pantalla fuera de la carcasa lo máximo posible, presionar en la parte baja del cristal hasta que se suelte ligeramente (~1mm).
Usar los pulgares para deslizar el cristal por debajo de la carcasa hasta que la parte superior se separe.

I found the adhesive (or fit) quite strong. Pushing on the bottom part of the glass created a small gap at the top, which I could fit a craft knife (xacto blade) into. This made it easier to carefully lever the glass out for me.

aaaidan -

I slipped and broke the LCD. So !#^&@@ off. What an absolute bastard of a job!

lf - 02/05/16

What is the "rear edge" of the nano? Can this be a bit clearer please? Maybe a video of this step would be a good idea. Then again, since Apple owns this site, I guess that's not gonna happen, is it?

lf - 02/05/16

I don't see "rear edge" anywhere in the instructions. I do see "lower edge" a few times and it looks pretty clear to me. I did this repair a couple years ago without much trouble.

Rene Jeddore - 03/05/16

You could do all these steps and really mess up your nano. Instead of disassembling the iPod, carefully remove the remnants of the old glass which I assumed you have cracked. With the new glass in hand CAREFULLY sand one edge of the glass evenly. I used my fine grinder on my dremel tool. After assuring a snug fit I removed the adhesive and installed the glass. Looks great and functional and I didn't ruin my iPod in the process. And when I said sand one edge I mean one of the edges that has a "lip" on it. The other lip you can slide right in and push gently down for a nice fit. Do not remove the adhesive until you are sure of a good fit. This is a quick fix for those who are too queezy to take apart their device.

Jim - 06/01/17

My battery had expanded and pushed out the glass enough for me to peel the glue out like a battery pull tab on a phone so it was pretty easy to remove, but the screen is giving me some trouble. The expanded battery is holding the screen to the frame making it more difficult to remove.

Elijah - 28/11/20

Absolut falsch beschrieben, die Anleitung ist

Herbert - 02/05/21

Grottenschlecht

Herbert - 02/05/21

Lieber Herbert,

schade, dass dir die Anleitung bisher nicht geholfen hat. Stand heute haben bereits 35 andere Nutzer ihr Gerät damit erfolgreich repariert, deshalb wäre es gut zu wissen, was genau bei dir nicht geklappt hat und wo es hakt?

Unsere Anleitungen werden nach dem Wikipedia-Prinzip geschrieben, das heißt du kannst auch selbst jederzeit noch zusätzliche Punkte hinzufügen oder Änderungen vornehmen, die besser beschreiben, was hilft, damit für diejenigen, die nach dir diese Reparatur versuchen, eine noch umfassendere Dokumentation zur Verfügung steht.

Sandra Hiller - 03/05/21

Paso 7

Separar el cristal de la carcasa del iPod Nano.
Antes de volver a instalar el cristal, asegúrate de limpiarlo bien, sobre todo de huellas de los dedos que hayan podido quedar en la parte interior del mismo.

Paso 8

Usa el borde de una herramienta de apertura de iPod para separar el interruptor de retención del adhesivo que lo sujeta al borde superior de la pantalla.
El cable plano del interruptor de retención es extremadamente frágil y se rompe con facilidad. Trabaja suavemente.

Be extremely careful while doing anything around the screen. The slightest bit of pressure in the wrong direction and you will be replacing the screen along with the battery. I speak from experience.

Brian Campbell - 09/05/17

I was extremely careful… and, I broke the display! ~ Gah! ~ $18 for a new one on Ebay (half the price if I wanna wait 3-4x as long to purchase from overseas, twice the price if I buy it from this site!) ~ What a bummer! ~ The goal was to fix this for a customer, and instead I created a longer wait & obviously have to pay for the screen I broke. LISTEN TO BRIAN! BE CAREFUL! THE SCREEN _WANTS_ YOU TO BREAK IT! DON’T FALL FOR IT!

cybrosis catharsis - 13/03/20

Does anyone know where I could get the power button flex cable replacement? I was too extremely careful but the screen has a very precise fit. I is fine when you push the screen into the case but !&&* of a work to pull it out.

[deleted] - 18/03/20

Paso 9

Despega la cinta Kapton que cubre el enchufe del cable de datos de la pantalla.

Paso 10

Mientras sujetas el enchufe de color claro con un dedo, usa la punta de un spudger para voltear el bloqueo del cable ZIF hacia la parte inferior del Nano.

Continue to carefully hold the socket down while doing the next step. If the cable come off at the wrong angle it can pull the connector away from the board at the base of the screen.

Brian Campbell - 09/05/17

Paso 11

Utiliza una herramienta de apertura de iPod para despegar el cable de datos de la pantalla de la placa de metal delgada adherida a la pantalla.
Ten cuidado de no romper el cable de datos de la pantalla.

Some of the ribbon is inside the white housing with the lock on, it needs to slide out of the housing. I didn't notice this because everything is so small - be sure not to slide your pry tool right through it.

Martin Mccaffrey -

The display can actually be pulled out slightly further than it initially seems. When you gently pull it up, you'll experience some resistance, which I initially thought indicated it was as far as it could go. But an extra bit of (still very gentle) force can pull it up a few more millimetres, which means the opening tool can fit.

Also, it seemed to me to actually be helpful to lever the cable out of its port before removing the ribbon from the adhesive on the plate, since this allowed better access to the adhesive with the opening tool.

aaaidan -

As commenter Brian Campbell wrote on the previous step, it is important to hold down the white cable socket while carefully working the cable loose from the adhesive. Even a small amount of upward force on the display data cable while it is still inside the socket could be enough to tear the socket off the board. Try not to pry up - use a thin, new (undamaged) opening tool to get under the ribbon cable and keep it parallel and as close to the metal plate as possible. It needs to be worked *under* the data cable, not to pry, as the cable just slides straight out the bottom of the white socket.

Barry L. Kramer - 05/08/18

Paso 12

Saca la pantalla del Nano, teniendo cuidado con el cable del interruptor de retención que puede quedar atrapado.
Al sacar la pantalla de la caja, ten cuidado de no romper el cable del interruptor de retención.

WATCH THE HOLD SWITCH!! Be *sure* it is disconnected before pulling out the screen! (I've made that mistake too many times :P)

iTronics Repair -

disconnected from what?

I never saw where it was connected to!

Fred Rodolf -

By "caught" do you mean glued to the case? Mine was, and I cant tell how I could possibly have removed the screen without it breaking. Luckily my Ipod was already broken, but now its even more broke because of this guide.

swd311000 - 14/12/14

Oops!!!…..I managed to break the little ribbon cable going to the hold switch…lots of very “colourful“ words aimed at myself are in my head now.

Simon Kormendy - 29/05/21

Paso 13

Si está presente, retira la tira de cinta que cubre los componentes electrónicos de la pantalla.

Paso 14

El soporte de la pantalla está unido a la pantalla mediante una tira de adhesivo alrededor de su perímetro.
Usa el borde de una herramienta de apertura de iPod para sacar con cuidado el soporte de la pantalla de la parte trasera de la pantalla.
Continúa separando el soporte de la pantalla a lo largo del costado de la pantalla.