Reemplazo de la placa Wi-Fi de Nintendo DS Lite

Escrito Por: Matthew Newsom
  • Comentarios: 30
Reemplazo de la placa Wi-Fi de Nintendo DS Lite

Dificultad

Moderado

Pasos

10

Tiempo Requerido

10 - 25 minutos

Introducción

¿Tienes problemas para conectarse a Internet en tu Nintendo DS Lite? Reemplaza la placa Wi-Fi para volver a conectarte.

  1. VAkqhUG2ctFuiKKh
    VAkqhUG2ctFuiKKh
    eIKe4YBYXvQpmQZa

    • Desatornille el tornillo Phillips que sujeta la tapa de la batería a la carcasa inferior.

    • El tornillo permanece cautivo a la tapa de la batería.

    • Haz palanca en la cubierta de la batería hacia arriba con un spudger o una uña y levántala para sacarla de la caja inferior.

    A Phillips #000 (PH000) seems to give a more secure fit (no slipping) than the stated Phillips #00.

    Ritchie -

    This will be good for mods

    Matthew Bevins -

    I'm having a problem getting the screw to unscrew. I have the right Phillips ( it was included with all the stuff I got this) Any tips. it doesn't look like the screw is spinning but i haven't played my Nintendo DS Lite for 3 years.

    whittlegirls -

    bonjour j’ai une petite question pour vous fais trés longtemps que j’ai pas utiliser mon nintendo ds lite et quand je le branche il allume 1 fois orange après il s’enteint même s’il est brancher ça veux tu dire qu’il faut que je change de batterie ? Merci

    Marie-Julie Richer -

    Soit un changement de batterie, soit la carte-mère a peut-être un court-circuit :/

    Polaris -

  2. 25sZ5YeYaes4dCMx

    • Introduce el borde de un spudger entre el costado de la batería y la carcasa inferior y haz palanca hacia arriba para sacar la batería.

    • Retira la batería del DS Lite.

  3. TgU6hRLWjWFK4TCK
    TgU6hRLWjWFK4TCK
    CMk1E2IEHDrjmKjB

    • Usa la punta de un spudger para levantar ambas patas de goma del DS Lite

  4. 5mujrSp3TuXlBfCh

    • Quite los siguientes tornillos que sujetan la carcasa inferior al cuerpo del DS Lite:

    • Dos tornillos 4.3 mm gold Phillips

    • Un tornillo 3.9 mm black Tri-Wing

    • Un tornillo 3.3 mm silver Phillips

    • Tres tornillos 5.5 mm silver Tri-Wing

    Not mentioned is to remove the jumper/connector below the word "SLOT-2". Case WILL NOT separate otherwise.

    Kayla -

    In the separation step below, the third picture show the case with the jumper/connector removed.

    Kayla -

    I cannot remove the tri-wing screws.

    Zach Smith -

    Same to me. I tried opening the case by force. Broke several parts of the motherboard…

    Leon -

    I can't remove the final tri wing screw in the battery section and it looks like I grinded the screw out too much for any screwdriver to work.Is there anything I can do?

    Quintin Harbin -

    From what I know, the only solution is to drill the screw out with a very small-headed drill :/

    Polaris -

    How to remove a stripped screw

    Gena FM -

  5. wZxqpiHuTIdWhnk5
    wZxqpiHuTIdWhnk5
    RKCEoKJwEHK44LCO
    pSLANlQhrJj1jOZH

    • Retira la tapa de la ranura del Game Pak antes de continuar.

    • Inserta el borde de un spudger entre la caja inferior y superior cerca de la esquina superior derecha del DS Lite.

    • Pasa con cuidado el spudger a lo largo del borde derecho del DS Lite, creando una abertura en el proceso.

    • Continúa pasando el spudger por la parte trasera de la DS Lite hasta que la mayor parte de la caja inferior se haya separado de la caja superior.

    Don’t forget to remove the GBA cartridge placeholder before removing the backside

    Cees Jan de Boer -

    You forgot to mention to remove the battery compartment Phillips screw.

    nathan lowe -

  6. ogeB4h5PpuF5FBNh

    • Levanta la carcasa inferior del resto del DS Lite.

    • Tira con cuidado. Algunas unidades están selladas con adhesivo y tirar demasiado fuerte puede dañar el interruptor de encendido.

    • Al volver a ensamblar, asegúrate de que el interruptor de encendido y los controles deslizantes de volumen estén correctamente alineados con los interruptores de la placa base.

    When you reassemble, make sure that you have the volume and power buttons in place, and make sure they are in the right position to line up with the switches on the motherboard. If they are not aligned, you risk snapping off the tiny switches on the motherboard (in which case, you are in for some soldering work).

    Eric -

    I should have read the comments first - broke off the power switch because I didn't know about aligning it. No way I can do soldering, guess it's for the dustbin :-(

    Emma -

    Whoops, remembered the power button but forgot the volume slider.

    I'll do it later.

    analbonghits -

    There is no way that the fact you have to line up the volume and power switch toggles upon reassembly is not in this guide. I just carefully followed this guide to replace the shoulder buttons but ruined my DS lite because I didn’t read these (practically hidden comments due to the design of the website) comments and broke the power switch. Thankfully there are 150 million DS I can buy second hand but “repeat the steps backwards” wasn’t sufficient in this repair. And that’s what this website is for.

    Ryan -

  7. D6jD6OGIIu5DcBNn
    D6jD6OGIIu5DcBNn
    yAQV5QhABedWTwIH

    • Levanta ambos botones disparadores del DS Lite.

    • Los botones del gatillo se sujetan muy holgadamente mediante pequeñas clavijas y resortes de metal. No pierdas de vista estas piezas.

    • La segunda imagen muestra la configuración correcta del conjunto del gatillo para el reensamblaje.

    Anything after step 7 is unnecessary if having to replace the left or right trigger button(s).

    Nate River -

    The second picture does not show the correct configuration of the button spring. It should be flipped. Look at the trigger on the left of the larger image; that is the correct configuration.

    wrekone -

  8. Mu2ZYeJKEcduVNJC

    • Usa el borde plano de un spudger para levantar el conector de la antena Wi-Fi de su zócalo en la placa Wi-Fi.

    There is absolutely no need to follow steps 8-13 if like me, all you needed to do was access the face buttons for cleaning/replacement. Once you have unscrewed the motherboard from the front casing you can just flip it up, making sure you take the front screen with it. You will have full access to the buttons and all of their contacts. No need to remove the wifi board and microphone cable, etc. Also, replacing the ribbon cables for the screen is especially frustrating. Avoid taking them out at all costs, if you can.

    James McCarthy -

    what is the "etc."?

    Rita Cao -

    For those replacing the bottom screen, you can just skip to step 13 and go from there. No need to remove the wifi board, antenna, etc.

    lowestseries -

  9. kJJ6hKr4VDWRNeyJ

    • Usa el borde plano de un spudger para sacar el conector de la placa Wi-Fi de su zócalo en la placa base.

    the i was working on had a different wifi connector. i thought a had broken it but the thing underneath it was just to balance it on the motherboard.

    BigD29853 -

    Do you have to put back in the WiFi board? As far as I know it does not require it to play games.

    Aiden Harlin -

    With the Nintendo servers now off, and all the games are playable without WiFi. That being said, I don’t know what is used for local multiplayer.

    Polaris -

  10. hsrcSov5XWaC2ETO

    • Usa el borde plano de un spudger para separar el borde derecho de la placa Wi-Fi de la placa base.

    • La placa Wi-Fi está asegurada a la placa base con una capa de adhesivo.

    • Quita la tarjeta Wi-Fi del DS Lite.

    I took it apart successfully and I replaced the screen but I've put it back together and it the green light turns on for about 2seconds quiet dim, brighter for about 1 and then it turns off... I then took the wifi board out, and it turned on! What have I done to it and why doesn't it work with it and only without?!

    Brianlewis -

    Exact same symptoms for me : on boot up, green light would stay on for 1 second, then shut down. Without wifi, green light would stay on, but blank screens. In fact, it's because on boot up, DS will check if wifi is present, and stop if there is an error. Then, it checks for upper screen, and after that, for lower screen. If one of these is not responding, DS will turn off. I check my cables (upper screen) and DS started again with no problem.

    Alexandre -

Conclusión

Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.

Autor

Matthew Newsom

Miembro Desde 06/01/10

38224 Reputación

2 comentarios

So I came across a "Prison edition" DSLite out of the Kentucky DOC It I was told that the wifi card was disabled but I take it apart and see that it is still there pluged in and everything you don't happen to know how to turn it back on do you it is a gift for my little brother and would like the WiFi to work.

Vincent -

Question anyone knows what the pin layout of the board

Aaron Darren -