Reemplazo de la placa base del Samsung Galaxy Watch Active2

Escrito Por: Tobias Isakeit

Comentarios: 21

Reemplazo de la placa base del Samsung Galaxy Watch Active2

Dificultad

Moderado

Pasos

Tiempo Requerido

35 minutos - 1 hora

Introducción

Usa esta guía para reemplazar una placa base defectuosa en tu Samsung Galaxy Watch Active2.

Herramientas

Paso 1

Apaga el Galaxy Watch Active2 manteniendo presionado el botón inferior durante aproximadamente 3 segundos. Deberías sentir una vibración corta.
Cuando aparezca el símbolo de "Power off", toca el centro de la pantalla para que se apague. Deberías sentir una vibración más larga para confirmar.

Paso 2

Usa un destornillador Tri-point Y00 para quitar los cuatro tornillos de 4 mm de largo en la parte posterior del reloj.

Y1.5 works just as good

BRIAN MIRANDA -

Paso 3

Usa una púa de apertura y colócala entre la tapa trasera de plástico y la carcasa de metal cerca de los botones.
Empuja la púa de apertura en el espacio para separar la tapa trasera de la carcasa.
No quites la tapa trasera del todo todavía. Hay un cable que lo conecta a la placa base.

There is a glue-ish gasket keeping it closed. I used an exacto knife to start it opening.

BRIAN MIRANDA -

This was super helpful thank you! Perfect timing

this is trash -

Waarmee kan ik de achterste oplaadplaat weer vast lijmen op de achterste behuizing

Ilona Smit -

Paso 4

Levanta con cuidado la tapa trasera para acceder al conector del conjunto de sensores.
Usa un spudger para desconectar la matriz de sensores de la placa base.

Ou je peu me procurer le tourne vis tri point 000

grenierlulu -

Paso 6

Utiliza un spudger para desconectar la pantalla y el altavoz

Paso 7

Usa un spudger para desconectar el sensor barométrico, los botones y el micrófono.

Paso 8

Coloca un spudger debajo de la placa base en la parte superior derecha al lado del conector de la pantalla.
Gira ligeramente y haz palanca con el spudger para aflojar el conjunto central.
Puede que te ayude revisar también los comentarios debajo de esto y el siguiente paso si tienes dificultades.

I would not suggest to do so. There are components underneath the motherboard as well. There are none in this specific corner, but the core assembly does not come out that easily and people might try other corners and positions. Rather unscrew the motherboard and remove the battery from the core assembly directly.

Nicola Tambascia - 09/08/22

Paso 9

Toma el conjunto central y deslízalo con cuidado para sacarlo de debajo de los cables.
Retira el conjunto central

I had to remove that screw on the core assembly using a Phillips 000. When I initially tried lifting, the core assembly started to bend. Mine also has a connector under the core assembly near the thumb in the picture. The connector goes from the underside of the core assembly to the screen/body. It prevents me from removing the core assembly as I'm not sure how it should be removed examining it

Louis Finney - 20/09/21

This step is really difficult, and I'm still not sure it was necessary. The core assembly is really packed in there, and it took me several attempts, lifting from various corners. Don't pull by the circuit board. It will bend if you're not careful. You've got to get under the core assembly. I had the most luck starting next to the display connector at the top, then moving to the sensor on the other end of the board (barometric sensor), then moving to the speakers on the left, and finally lifting from multiple points once it was out far enough. In really hoping I didn't damage anything.

Karl Arp - 27/05/22

I think the comments here should be added to the step before.

Nicola Tambascia -

Paso 10

Dale la vuelta al ensamblaje central para que la placa base quede hacia abajo.

Paso 11

Usa la punta de una púa de apertura para despegar el botón superior del marco de plástico.

Paso 12

Usa un destornillador Phillips para quitar el tornillo de 4,4 mm de largo que sujeta la placa base en su lugar.

Paso 13

Coloca el extremo plano de un spudger entre la placa base y el marco de plástico cerca de la bobina de cobre en la parte inferior derecha.
Gira el spudger para liberar la placa base de las pestañas de plástico.

Paso 14

Desliza la placa base por debajo de las pestañas de plástico restantes para quitarla.

Conclusión

Compara tu nueva pieza de repuesto con la pieza original; es posible que debas transferir los componentes restantes o quitar los respaldos adhesivos de la nueva pieza antes de instalarla.

Para reensamblar tu dispositivo, sigue estas instrucciones en orden inverso.

Lleva tus desechos electrónicos a un centro de reciclaje certificado.

¿La reparación no salió como planeado? Trata unas resoluciones de problemas básicos, o pregunta nuestra Comunidad de respuestas por ayuda.

Autor

Tobias Isakeit

Miembro Desde 31/03/14

108306 Reputación

12 comentarios

Hi, I am having issues with bluetooth, is it a replacement or do I need to swap the MB? Thank you

Bruno Albin -

When you have ruled out any software issues (tried restart, factory reset, software update, etc) then this is most likely a MB replacement since all the modules are integrated on that tiny thing.

Tobias Isakeit -

does the watch active have the same motherboard as the watch active 2

aqoullam6 -

Nope, the Watch Active has a different motherboard.

Tobias Isakeit -

My watch stopped vibrating all together, which part do I need to replace?

Melissa McEleney -

This would be the vibration motor which is located under the battery (small cylindrical component on the bottom right with two golden contacts) seen in the last picture.

Tobias Isakeit -

My active 2 watch has water damage is it cheaper to replace the part or parts or get a new one at this point?

The screen has 0 response.

Jeyanth Parameswaran -

You can always try and open it up to assess the damage and see which parts need replacing.

Tobias Isakeit -

My watch stopped working after swimming in a pool, What part/s could it be that needs replacement?

prateek tamta -

Hard to say. But you can always try and open your watch to assess the damage and see which parts need replacing.

Tobias Isakeit -

My watch is flickering .. What can I do ? what part need to be replaced?

Mary West -

If still under warranty, you might want to try and contact the seller.
If the watch is out of warranty it could be a loose display connector (try that first), a defective display, a weak solder joint or maybe water damage.

Tobias Isakeit -