Reemplazo de la placa de control delgada de PlayStation 3

Escrito Por: Andrew Bookholt
  • Comentarios: 21
Reemplazo de la placa de control delgada de PlayStation 3

Dificultad

Moderado

Pasos

6

Tiempo Requerido

5 - 15 minutos

Introducción

Utiliza esta guía para reemplazar la placa de control. Reemplazar la placa de control proporcionará un nuevo panel de espejo, un botón de encendido y un botón de expulsión.

  1. sbUCUYRWF5u33DHo

    • Dale la vuelta a tu PS3 y colócala con la parte trasera hacia arriba.

    • Con cuidado, quita la pegatina de la garantía, así podrás acceder al tornillo que se encuentra escondido debajo de ella.

    • Para evitar que la pegatina cree un vacío, calienta la pegatina y quítala con cuidado para poder reemplazarla limpiamente.

    Don’t even need to bother with the sticker anymore since SONY does not care what you do with them anymore.

    Travis Wheeler -

  2. fktNXIVQYKIbefHS
    fktNXIVQYKIbefHS
    Z2lGLuRFjeG6aFvV

    • Utiliza la parte plana de un "spudger" para hacer palanca en los siete puntos que se encuentran en el borde de la carcasa inferior y que esconden bajo ellos tornillos. Puedes observar en la imagen dónde están localizados.

  3. u6tkxEEWjBggtSMy

    • Quita los siete tornillos Phillips de 37mm que sujetan la tapa superior de la carcasa inferior.

  4. BuJcUHDpFwOwPFDL

    • Quita los cuatro tornillos de seguridad Torx T8 de 13.3 mm que se encuentran debajo de la apertura del Blu-ray. (Algunos modelos solo cuentan con (3)tres tornillos)

    Its 4 screws beneath the blu-ray

    Manuel -

    Remove the four 13.3 mm T8 security Torx screws beneath the Blu-ray drive opening.

    Daniel Tlapa -

    Can we edit this to say 4 screws?

    revanantwraith -

    I made the change from three to four screws, but you're able to edit the guides as well. If you want to edit something, you can click the Edit link on the right side of any guide step, or the Edit link at the top right of the page (sandwiched in-between View and History).

    Taylor Arnicar -

    Do you guys have a guide for the PS3 Slim Model 3001A. The fan is different than this model.

    emknight04 -

    3001a is basically same motherboard but cheaper plastic bd drive other than that its exactly the same until you get to the new slim line

    Robert -

    Anyone know an online retailer with a competitive price for the replacement fan?

    Jared -

    My PS3 had only three Torx screws. Having four in the diagram was initially confusing. Obviously they made a mid-stream change at some point (mine is several years old now).

    corygbooker -

    I've accidentally removed the ribbon cable from the blu-Ray drive and can not seem to figure out how to reconnect it. Can anyone help?

    OneIfByLand -

    Take the top off the drive, connect the ribbon to the motherboard then replace the drive sliding the ribbon through the slot on the bottom of the drive and reconnect to the laser.

    KcXbox Repair -

    pls help i have to tear down my ps3 slim but the 4 srews are very hard to take it out because there is a needle in the middle pls hep

    Vincent Brabandt -

    If the screw has a pin in the center, that means it is a security Torx meant to prevent tampering. To remove this screw, follow the guide I have linked below...

    http://www.instructables.com/id/Removing...

    Telpack -

    How do u buy the screw driver for these screws

    mistergalacta hoggy -

    Online at the usual suspects?

    Or some hobby stores or places that sell tools will sometimes carry these.

    revanantwraith -

    Anyone else's screws for this step need the T7 bit instead of T8?

    Michael J Cotton -

    What is the name of this screwdriver

    Mohammad Shawa -

  5. LvQrCIDkbymnDdoa
    LvQrCIDkbymnDdoa
    QhXCIUkPgeFEM2N3

    • Levanta la tapa superior desde el borde trasero y rótala hacia la parte frontal de la PS3.

    • Quita la tapa de la PS3.

    I just want to open the top cover to clean the fan. Do I need to unscrew the four security screws?

    Aryan -

  6. kKvUGXOJlQeZDjrY
    kKvUGXOJlQeZDjrY
    Zan2LOWEfoIavRLe

    • Usa la punta de un spudger para sacar la placa de control de su alojamiento dentro de la caja inferior.

    • Saca el cable plano de la placa de control de su zócalo en la placa de control.

    Please do a review on how to do this on a Cech 3001b but only how to plug in the wire

    Darian -

Conclusión

Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.

Autor

Andrew Bookholt

578639 Reputación

2 comentarios

I have a PS3 slim that won't turn on, unfortunately my Power/eject button and ribbon cable are completely removed from my PS3. Can I turn it on without the button/ribbon cable?

wrestlemaniafreak -

I replaced the entire psu but without a standby light I have no idea if I'm close to powering it on. I suppose I could get a multimeter but I don't know what I'm testing. Any info would be appreciated.

wrestlemaniafreak -