Reemplazo de la unidad óptica MacBook Pro 13" Unibody a principios de 2011

Escrito Por: Andrew Bookholt
  • Comentarios: 43
Reemplazo de la unidad óptica MacBook Pro 13" Unibody a principios de 2011

Dificultad

Moderado

Pasos

11

Tiempo Requerido

No hay estimado

Introducción

Prereq interno.

  1. x6UWNSW21HTJwlMV

    • Usa el lado plano del spudger para hacer palanca y extraer el cable plano del conector con la placa madre correspondiente al AirPort/Bluetooth.

    N.B! Thank you very much all you here on iFixit! Some IMPORTANT notes. Be very careful BEFORE prying the connectors up and down. They are very fragile and the picture could actually be seen as showing a bending loading in their weakest direction, AROUND its slender axis. The connector is slender and inserted on the logic board, so the gentle "walking" up and down should be done ALONG their slender direction and WITHOUT touching the adjacent connectors. If bending is done around its axis the soldering comes apart and the cable is done and gone. Just happened. These flat cables are one of the weakest design spots in my experience. They are a major time, money and geist consuming reason for malfunction like Wi-Fi connection problems, HDD, SSD not found internally but externally from USB issues et al being found on different forums. Thanks again and again.

    Greg -

  2. cEP5OeAoPdHLaIPT

    • Con mucho cuidado estira el cable de la cámara de su conector en la placa madre.

    • Aunque se desaconseja por los expertos de iFixit, algunos usuarios optan por saltarse este paso. Para más información, véase los comentarios.

    • Estira el cable de forma paralela a la placa madre. Si lo estiras hacia arriba es posible que dañes la placa madre o el cable.

    I'd to disassemble my MBP two times because my SSD did not work properly in optibay. While doing it a second time, I omitted steps 6 and 8. It is really not necessary, but step 6 is really scary.

    nicholas -

    Do you even need to do this?? I've seen guides where they just leave those on and slide the superdrive out from underneath that module..??

    Philip -

    Yes, this is really no need. I left it there, and still can proceed.

    maiyawmh -

    I've replaced 4 dvd's with hdd's already, in different macbooks, so wasn't too fussed about #5. However; this time I broke the camera connector cable :(

    The connector is stil in it's socket, and I can't get it out no matter what I try. My guess is that some of the glue that connects the socket to the logic board, got into the socket as well. Prying with a small screwdriver, pulling with a pair of tweezers... nothing works. And this mbp belongs to a friend who uses his camera a lot for skyping...

    I hope we're still friends after I tell him.

    The thing is; I think it might be possible to do the whole operation with that cable still in its sockets; if you pull the rest of the cable free of the fingers, you can probably fold it out of the way when you lift the dvd out.

    puchelaar -

    This is Sooo Unnecessary!! don't do it!

    grant reynolds -

    I actually found it necessary to do this step. If not done you can rip chord, if you read the wording carefully and do as it says it should not break.

    Robert Wacker -

    After having initially skipped this step, I finally followed it. I couldn't find a way to move the airport / bluetooth assembly away otherwise, and in the end it's a pain to put the small screws back in. Didn't have any trouble unplugging the camera cable, but it is indeed scary because it looks pretty fragile.

    I only skipped step 8, as it didn't seem necessary.

    JoGersen -

    I also broke my camera cable!!! And I just realized that removing that lovely cable was not necessary for the following steps!!! Thank you!

    I dont know how to fix this problem and I asked it in this question: How can I fix broken camera cable

    Please, help...

    Yusuf -

    I successfully skipped this step when removing the hard drive enclosure (I had already the dual drive running, but I needed to replace the drive in the optical enclosure. I also skipped steps 7, 8, and 11.

    pauloau -

    I have a blog post on my experience of performing the upgrade with a simple diagram showing how to skip step 6, 7, 8 and 11. (http://www.ocyedwin.com/?p=190)

    Aderic Adsisco -

    I tried to pull the cable, but it did not come off even with moderate force. So it stayed as it was, and I had no problems taking out the drive and putting in the new one.

    Probably its best to skip this step.

    cearnach -

    I can't remove this so I skip it. I also skip 7,8,11 with no problem, just do it slow and carefully remove any parts.

    Pat Ach -

    Just did this. I elected to actually do this step and I’m glad I did. It was no big deal. Just pull straight back from the socket (not up or angled!) and although it was a little tight, it came out. I think it’s worth it not to possibly mess that cable up when you extract the drive. The drive itself does not lift up straight out- you have to work it out as there a few minor obstructions. At that point, it would be very easy to damage the camera cable. I took all the antenna cables off even those this guide only recommended taking off the long cable. This was due to an Apple repair video I had seen. This proved to be unnecessary and I should just have stuck with this guide’s recommendation. I did skip taking the woofer cable off towards the end of this guide as that seemed to be, and subsequently proved to be, utterly unnecessary. All in all, just moving slowly and carefully I managed this in 30 mins though next time will be faster, no doubt.

    dave -

    I did not perform step 6, 7, 8, 10 and 11. Once I performed step 9, I was able move the speaker housing to the right enough to get a long screwdriver to get to the ‘hidden’ screw underneath the housing and just removed the other two main screws holding in the drive in step 14. I did remove the HDD and holding backet prior to starting so I could slip the superdrive out and place the caddy back in the opposite direction. You just have to careful not to snag the wires when trying to remove the superdrive and and when slipping in the caddy. My Macbook is a MacBook Pro (13-inch, Mid 2012) and I only needed a Philips 00 screwdriver, and did not need to use a Torx screwdriver during any part of the upgrade.

    Balvinder Gill -

  3. BYDTQ3c2nmTExkJV
    BYDTQ3c2nmTExkJV
    FPQBWIKJHu1nKXo3

    • Con mucho cuidado aparta el cable plano del AirPort/Bluetooth mientras despegas el cable de la cámara de su adhesivo de seguridad hacia el subwoofer y la abrazadera del AirPort/Bluetooth.

    • Extrae el cable de la cámara de la cavidad moldeada en el soporte AirPort/Bluetooth.

    This step is unnecessary, as is step 8. You can get the SuperDrive out and put the caddy in without pulling the cable out.

    Steve -

    I successfully skipped this step when removing the hard drive enclosure (I had already the dual drive running, but I needed to replace the drive in the optical enclosure. I also skipped steps 6, 8, and 11.

    pauloau -

    Confirmed for a second time: Steps 6, 7, 11 NOT NEEDED.

    Alvaro Paiva Bimbo -

  4. p6dfGBNIeyinfMwa
    p6dfGBNIeyinfMwa
    aG5RsEcxeCUNsPyR

    • Utiliza la punta de un spudger para hacer palanca en el conector de antena más cercano a la placa lógica desde su zócalo en la placa AirPort/Bluetooth.

    • Desenruta el cable de antena desde debajo del dedo moldeado en el soporte AirPort/Bluetooth.

    I successfully skipped this step when removing the hard drive enclosure (I had already the dual drive running, but I needed to replace the drive in the optical enclosure. I also skipped steps 6, 7, and 11.

    pauloau -

    Based on the advice above, I tried to skip this step. Unfortunately, the way the wire wraps around the plastic caused it to break underneath when I lifted the optical drive out, and now I have another broken part.

    lisaquatmann -

    Yu can easily skip the step, just make sure you take care when removing/put away the AirPort/BT assembly in the next step, be gentle.

    Lucian Onea -

    I skipped this step and disconnected (the end that was not mentioned) accidentally from the machine, what can I do to repair it?

    Ely -

    Ce connecteur est très fermement fixéà la carte. Lorsque j'ai procédé comme expliqué ici, il s'est brisé !!!!

    J'ai tenté de le recoller. Pour l'instant il semblerait que j'ai toujours du wifi. Ouf.

    Je pense donc qu'il faut éviter cette étape si possible.

    Pat Microbiom -

  5. Zu2TjZacS5IdmnGD

    • Retira los cinco tornillos siguientes:

    • Dos tornillos Phillips de 10,3 mm

    • Dos tornillos Phillips de 3,1 mm

    • Un tornillo Phillips de 5 mm

    Note the position of the little grounding rings when removing the red (10mm) screws. You'll have to make sure to re-seat them when reassembling!

    James -

    You are so right about making sure to put back the two metal rings when you screw back the two (red) 10.3mm screws. I missed putting back one of the rings and read your comment after I had installed the drive and closed the macbook. Everything was working fine, but I went back to open it an leave it just as it was, with both metal (one with a plastic/cloth material around it) plates/rings attached properly. So it is very important to make sure you put those two 10.3 mm screws back with the plates/rings that they hold, exactly as they were before you put it apart.

    pachis2 -

    I think you should remark when re-assembling the machine, you should pay attention to the metal clip in Step 9, the upper left screw position, it's easy to miss when assembling, because there are so many wires, and it may be very easy forgetting putting the metal clip back in place.

    Fisher -

    As far as the grounding ring goes, it slips back over the screw hole, be patient and gentle. You may have to finagle the airport board under it first and then lay the board flat and reattach the subwoofer. I will see if I can add a pic in the near future. But that the best way to describe it.

    Robert Wacker -

    FYI: These are #00 Phillips screws!

    Rossi Macri -

    Help! I think i stripped the screw head of the one encircled in yellow. What to do?

    BJC -

    Be weary of the cable when screwing in the Orange screw closest to the clutch cover. I pinched that cable and had to replace it.

    Duck -

  6. epc2CAE6J2wHkMMh
    epc2CAE6J2wHkMMh
    QxJxBUOplSqjH43W

    • Tira del conjunto AirPort/Bluetooth y el subwoofer hacia arriba cerca del centro del lado de la unidad óptica hasta que se despejen entre sí.

    • Aleja el conjunto AirPort/Bluetooth y el subwoofer de la parte superior de la unidad óptica.

    The left part in the picture (the AirPort/Bluetooth assembly) is held down under a plastic tab that sticks out a tiny amount. Thus, it needs to be pulled very slightly towards the camera module in order to be able to lift out.

    Darren -

  7. vaPvxZSYxuhceanU
    vaPvxZSYxuhceanU
    WZOvs2nGRZBp1W4Y

    • Tira del cable del altavoz/subwoofer derecho de debajo del dedo de contención cerca del lado de la unidad óptica.

    • Tira del cable del altavoz/subwoofer derecho hacia arriba para desconectarlo de la placa lógica.

    I will confirm for a third time, having just done this replacement yesterday morning: Steps 6, 7, 11 NOT NEEDED.

    cjdow -

    When I attempted to lift this cable out of the connector, the connector broke and separated from the board. I suggest not to do this step.

    car rider -

    Agreed. I skipped this step. No need to risk breaking a cable or connector if you don't have to disconnect it to get the optical drive out.

    Alan Grassia -

    Three things:

    1. Thanks for this guide!

    2. I don't understand the comments that this step (#11, disconnect the speaker cable from the logic board) can be skipped, given this guide is all about replacing a failed right speaker/subwoofer. Maybe this step was re-titled from its original post?

    3. My (used) replacement part from iFixit (part IF163-029-1) for my mid-2012 Macbook Pro 13" was different than the OEM part in that the replacement part's cable exited the subwoofer enclosure from the "northeast" corner of the package, rather than the "southeast" corner of the package. This required a rerouting of the cable to a route *on top" of the subwoofer rather than below it, as a nearby boss prevented the original route. Also, I needed to completely remove the heat shrink that joined the subwoofer and right speaker cables together near the connector, as it prevented the radius necessary to route that portion of the wire. I have pics but I don't see how one can provide them in the comments.

    ROBERT ANTHONY PASSARO -

  8. 6LtflW5NOvK2Z6kL

    • Utiliza el extremo plano de un spudger para sacar el conector del cable del disco duro hacia arriba desde su zócalo en la placa lógica.

    • Dobla el cable del disco duro lejos de la unidad óptica.

    N.B! Thank you very much all you here on iFixit! Some IMPORTANT notes. Be very careful BEFORE prying the connectors up and down. They are very fragile and the picture could actually be seen as showing a bending loading in their weakest direction, AROUND its slender axis. The connector is slender and inserted on the logic board, so the gentle "walking" up and down should be done ALONG their slender direction and WITHOUT touching the adjacent connectors. If bending is done around its axis the soldering comes apart and the cable is done and gone. Just happened. These flat cables are one of the weakest design spots in my experience. They are a major time, money and geist consuming reason for malfunction like Wi-Fi connection problems, HDD, SSD not found internally but externally from USB issues et al being found on different forums. Thanks again and again.

    Greg -

  9. RXGyW1msS4eGENwr

    • Utiliza el extremo plano de un spudger para sacar el conector de la unidad óptica hacia arriba desde su zócalo en la placa lógica.

  10. rAUl4NS6Yn2wDTLD

    • Retira los tres tornillos Phillips de 2,7 mm que fijan la unidad óptica a la caja superior.

    can i reuse this optical drive again

    justcause3 -

    Sure you can. Use it in anything. Stick it in a USB enclosure and carry it.

    scottmilliken -

    iFixit has a guide on How to Remove a Stripped Screw: Cómo quitar un tornillo barrido

    Stripped Screw -

    I stripped the top left screw and lost a few others, where can I buy replacements?

    Ely -

    top left screw is a nightmare

    Fabian Cadiz -

  11. MuTL3D1UNIy3VQiT

    • Tira de la unidad óptica hacia arriba desde su borde más cercano a la pantalla y retírala de la caja superior.

    Because I skipped steps 6, 7, 8, and 11. when removing the hard drive enclosure (I had already the dual drive running, but I needed to replace the drive in the optical enclosure, I found it easier to remove the enclosure by lift the side close to the battery and main HD and pulling it towards myself (towards main HD and battery).

    pauloau -

    Did the same, also because i skipped those steps. It worked, you just have to remove it gently.

    Lucian Onea -

Conclusión

Para volver a montar el dispositivo, sigue estas instrucciones en orden inverso.

Autor

Andrew Bookholt

578639 Reputación

0 comentarios