Reemplazo de los botones de control del iPod Shuffle de 4ª Generación

Escrito Por: Andrew Bookholt
  • Comentarios: 9
Reemplazo de los botones de control del iPod Shuffle de 4ª Generación

Dificultad

Difícil

Pasos

11

Tiempo Requerido

No hay estimado

Introducción

Reemplaza la parte electrónica de los botones de control.

  1. 11FbyVfUZdAV1j6D

    • Acceder a las partes internas de la 4ª generación de Shuffle es extremadamente difícil, ya que el panel posterior está pegado a la caja frontal y está asegurado con clips de retención metálicos. Es muy poco probable que puedas quitar el panel posterior sin causar daños estéticos y / o estructurales.

    • Antes de continuar, asegúrate de que su Shuffle esté apagado.

  2. nmhgjMNhTPmjkgfP
    nmhgjMNhTPmjkgfP
    tUBOLibUkW1n2JBl

    • Usa una combinación de herramientas de apertura para iPod y spudgers metálicos para separar el panel posterior del Shuffle por la costura más cercana al interruptor de ENCENDIDO / APAGADO.

    I managed to open mine using no tools at all so without damage. Maybe the glue also weakened over time so might need to use some heat. I didn’t but then again it’s a second hand, old device in my case.

    I used the clip on the back as a leverage to (ever so slightly) bend the back piece in the center. Having that bend is enough for the very small clips on the power switch side to detach. Once that side is removed you can slide the complete back out towards the direction of the power switch. I checked on a flat surface and the piece isn’t damaged, still straight. Just don’t keep it bend too long and don’t over bend it. It really shouldn’t take much since those notches are really small.

    To close it again just slide the back side in again and then snap the power switch side back in place by lightly pressing it on top. Since the clips aren’t damaged this way it will close up nicely. If the notches got damaged you’ll have to use glue instead (hot glue will do and is easily removable again).

    Ha ns -

    what do you mean by bend the back piece in the center?! How do you do that exactly? Did you stick something in between the back piece and the clip and press in?

    Jackson Chan -

    I completely agree with Ha ns' comment. I really cannot understand how the author managed to open this device as described. There must be something like a 0.1mm gap between the housing and the cover, impossible to enter a spudger or pry tool. Use a lever on the hinged side of the clip to lift the cover, insert a 0.2mm plastic film or a thin plectrum or spudger on the bent center of the cover. Avoid to push the spudger down, as there are electronic components underneath, only lift the cover, without overbending. Move over to the side of the on/off switch, and release the 3 clips. On the other end an 8mm long nose will avoid lifting off the cover. You will have to slide it out horizontally. Clearly: you have to be very very careful and gifted...

    cloclolulu -

  3. eAPkDt6GheQNokSX

    • Retira el panel trasero del Shuffle.

  4. YbIbPNiPXZ1ioDZg

    • Si está presente, retira el sello de humedad negro delgado que cubre los internos de Shuffle.

    • Retira el tornillo Phillips de 2.1 mm que fija la placa lógica a la caja frontal.

  5. YEuQVTPskVyTtyNP
    YEuQVTPskVyTtyNP
    OLAnfVMyZCGSypTC

    • Usa el borde de la herramienta de apertura de un iPod para levantar la solapa de retención del zócalo ZIF del cable del botón de control.

    • Asegúrate de que estés levantando la aleta de retención con bisagras, no el zócalo en sí.

    • Usa un par de pinzas para sacar suavemente el cable plano del botón de control de su zócalo.

    The cable was in so firmly that it tore off the socket coming out, any hope of attaching for someone with soldering skills?

    Jon -

    I could not get the ribbon cable out with a pair of tweezers. Instead I inserted a needle below the cable, and gently pulled it out by pressing with the finger on the cable (and against the needle). Very difficult!

    cloclolulu -

  6. AGHuau3savuaNuDt
    AGHuau3savuaNuDt
    e4QRKtNKta3msDPT

    • Usa una herramienta de apertura de iPod para extraer suavemente la batería del adhesivo que la sujeta a la caja frontal.

    • Saca la batería de la caja frontal, asegurándote de no forzar sus cables delicados.

    Why not simplifying this delicate step by just cutting the wires and soldering the (also cutted) new battery’s wires onto them (without creating a short circuit of course!)

    Frans Noordman -

    I was going to refer to my comment on step 10, where I am essentially saying this same thing and how to do it.

    If you don’t like the prospect of soldering to the logic board if you are new to it this is an easier way to get this job done without the risk of bricking the logic board, and you also wont have to disassemble the iPod any more than the guide has shown up to this point.

    Lars Alfred Henrik Stahlin -

  7. wXf1mKlTxtelDsnF
    wXf1mKlTxtelDsnF
    5beXcvroVVhOpBWI

    • Inserta la punta de una sonda de metal en el orificio moldeado en el retenedor de la placa lógica más cercano a la placa lógica.

    • Separa el retenedor de la parte frontal de la caja frontal, luego tira de él desde el lado de la caja frontal.

    • Retira el retenedor de la placa lógica del Shuffle.

  8. weDqqcpFcTAhwNeR
    weDqqcpFcTAhwNeR
    NSjNjanmrBrFcFuI

    • Usa el borde de la herramienta de apertura de un iPod para empujar el conector de los auriculares hacia el centro del Shuffle.

  9. eZ4pTudBBqqINs3d
    eZ4pTudBBqqINs3d
    HChCjI6pXYtbRvPE

    • Continúa empujando la placa lógica hacia abajo desde el borde superior del Shuffle.

    • Saca la placa lógica de la caja frontal por el lado más cercano al botón de ENCENDIDO / APAGADO y mueve suavemente el conector para auriculares fuera de su hueco en la caja frontal.

    • Retira el conjunto de la placa lógica del Shuffle.

  10. uqDpwvmBspSVKLeq

    • Retira los siguientes cuatro tornillos:

    • Dos tornillos Phillips de 1,2 mm con cabeza grande.

    • Dos tornillos Phillips de 1,6 mm con cabeza pequeña.

  11. pxJNiUEmcwKKVwNF
    pxJNiUEmcwKKVwNF
    4WgRZHRWS2iLyQnw

    • Utiliza una herramienta de apertura de iPod para sacar la placa del botón de control de la carcasa frontal.

    • Retira los botones de control del Shuffle.

Conclusión

Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.

Autor

Andrew Bookholt

578639 Reputación

2 comentarios

I'm gonna try to remove the back cover with minimal prying to reduce cosmetic defects. The plan is to somehow remove the spring loaded clip by pushing out the lever pin, then drilling holes along the edge of the over wherre the 3 little hooks are (In this image, where the right thumb is touching. https://d3nevzfk7ii3be.cloudfront.net/ig...).

It would be great if someone could provide a closer look at where exactly the hooks are so I can position my 1.5mm drill bit better. Also, if you can to figure out how to remove the spring loaded clip mechanism without going through the 4 screws, that'd be awesome! I suspect the pin is held in place by just adhesive, but don't want to risk pushing too hard and causing defects. :(

Sam Waiban -

just open the clip past where it is suppose to open and it pops right off.

Ethan Chow -