Reemplazo de los botones del gatillo de la Nintendo DS Lite

Escrito Por: Matthew Newsom
  • Comentarios: 26
Reemplazo de los botones del gatillo de la Nintendo DS Lite

Dificultad

Fácil

Pasos

7

Tiempo Requerido

20 minutos

Introducción

¡Reemplaza los botones de gatillo de tu Nintendo DS Lite y vuelve al juego!

  1. VAkqhUG2ctFuiKKh
    VAkqhUG2ctFuiKKh
    eIKe4YBYXvQpmQZa

    • Desatornille el tornillo Phillips que sujeta la tapa de la batería a la carcasa inferior.

    • El tornillo permanece cautivo a la tapa de la batería.

    • Haz palanca en la cubierta de la batería hacia arriba con un spudger o una uña y levántala para sacarla de la caja inferior.

    A Phillips #000 (PH000) seems to give a more secure fit (no slipping) than the stated Phillips #00.

    Ritchie -

    This will be good for mods

    Matthew Bevins -

    I'm having a problem getting the screw to unscrew. I have the right Phillips ( it was included with all the stuff I got this) Any tips. it doesn't look like the screw is spinning but i haven't played my Nintendo DS Lite for 3 years.

    whittlegirls -

    bonjour j’ai une petite question pour vous fais trés longtemps que j’ai pas utiliser mon nintendo ds lite et quand je le branche il allume 1 fois orange après il s’enteint même s’il est brancher ça veux tu dire qu’il faut que je change de batterie ? Merci

    Marie-Julie Richer -

    Soit un changement de batterie, soit la carte-mère a peut-être un court-circuit :/

    Polaris -

  2. 25sZ5YeYaes4dCMx

    • Introduce el borde de un spudger entre el costado de la batería y la carcasa inferior y haz palanca hacia arriba para sacar la batería.

    • Retira la batería del DS Lite.

  3. TgU6hRLWjWFK4TCK
    TgU6hRLWjWFK4TCK
    CMk1E2IEHDrjmKjB

    • Usa la punta de un spudger para levantar ambas patas de goma del DS Lite

  4. 5mujrSp3TuXlBfCh

    • Quite los siguientes tornillos que sujetan la carcasa inferior al cuerpo del DS Lite:

    • Dos tornillos 4.3 mm gold Phillips

    • Un tornillo 3.9 mm black Tri-Wing

    • Un tornillo 3.3 mm silver Phillips

    • Tres tornillos 5.5 mm silver Tri-Wing

    Not mentioned is to remove the jumper/connector below the word "SLOT-2". Case WILL NOT separate otherwise.

    Kayla -

    In the separation step below, the third picture show the case with the jumper/connector removed.

    Kayla -

    I cannot remove the tri-wing screws.

    Zach Smith -

    Same to me. I tried opening the case by force. Broke several parts of the motherboard…

    Leon -

    I can't remove the final tri wing screw in the battery section and it looks like I grinded the screw out too much for any screwdriver to work.Is there anything I can do?

    Quintin Harbin -

    From what I know, the only solution is to drill the screw out with a very small-headed drill :/

    Polaris -

    How to remove a stripped screw

    Gena FM -

  5. wZxqpiHuTIdWhnk5
    wZxqpiHuTIdWhnk5
    RKCEoKJwEHK44LCO
    pSLANlQhrJj1jOZH

    • Retira la tapa de la ranura del Game Pak antes de continuar.

    • Inserta el borde de un spudger entre la caja inferior y superior cerca de la esquina superior derecha del DS Lite.

    • Pasa con cuidado el spudger a lo largo del borde derecho del DS Lite, creando una abertura en el proceso.

    • Continúa pasando el spudger por la parte trasera de la DS Lite hasta que la mayor parte de la caja inferior se haya separado de la caja superior.

    Don’t forget to remove the GBA cartridge placeholder before removing the backside

    Cees Jan de Boer -

    You forgot to mention to remove the battery compartment Phillips screw.

    nathan lowe -

  6. ogeB4h5PpuF5FBNh

    • Levanta la carcasa inferior del resto del DS Lite.

    • Tira con cuidado. Algunas unidades están selladas con adhesivo y tirar demasiado fuerte puede dañar el interruptor de encendido.

    • Al volver a ensamblar, asegúrate de que el interruptor de encendido y los controles deslizantes de volumen estén correctamente alineados con los interruptores de la placa base.

    When you reassemble, make sure that you have the volume and power buttons in place, and make sure they are in the right position to line up with the switches on the motherboard. If they are not aligned, you risk snapping off the tiny switches on the motherboard (in which case, you are in for some soldering work).

    Eric -

    I should have read the comments first - broke off the power switch because I didn't know about aligning it. No way I can do soldering, guess it's for the dustbin :-(

    Emma -

    Whoops, remembered the power button but forgot the volume slider.

    I'll do it later.

    analbonghits -

    There is no way that the fact you have to line up the volume and power switch toggles upon reassembly is not in this guide. I just carefully followed this guide to replace the shoulder buttons but ruined my DS lite because I didn’t read these (practically hidden comments due to the design of the website) comments and broke the power switch. Thankfully there are 150 million DS I can buy second hand but “repeat the steps backwards” wasn’t sufficient in this repair. And that’s what this website is for.

    Ryan -

  7. D6jD6OGIIu5DcBNn
    D6jD6OGIIu5DcBNn
    yAQV5QhABedWTwIH

    • Levanta ambos botones disparadores del DS Lite.

    • Los botones del gatillo se sujetan muy holgadamente mediante pequeñas clavijas y resortes de metal. No pierdas de vista estas piezas.

    • La segunda imagen muestra la configuración correcta del conjunto del gatillo para el reensamblaje.

    Anything after step 7 is unnecessary if having to replace the left or right trigger button(s).

    Nate River -

    The second picture does not show the correct configuration of the button spring. It should be flipped. Look at the trigger on the left of the larger image; that is the correct configuration.

    wrekone -

Conclusión

Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.

Autor

Matthew Newsom

Miembro Desde 06/01/10

38224 Reputación

6 comentarios

no no no no no

seng -

Thank you this helped a lot I can finnaly play Zelda and Mario Cart now

MattTheGamer 49 -

Hi! I am attempting a trigger repair, but it seems the console was opened and worked on before I got my hands on it, and the switch for the trigger snapped off the board. I taped it to the board to test, and it still works. Is my best bet soldering the switch back to the motherboard? Or could I get away with superglue? (I've never soldered before, and this looks delicate)

Tamara Girodie -

I would definitely solder it, usually, these triggers are the ones that get the most stress and dirt around them so superglue might not last that much. If you have a problem with the trigger still. You might want to check the video I uploaded, it is in Spanish, though. https://youtu.be/7GRzZh9ZdNM

spinomagnus -

I dont get how removing them is supposed to fix it. it says you need no parts. someone explain

ur mom -

This gives you access to them and now you can clean them. There's some YouTube videos showing how, maybe some cleaning alcohol on a q-tip does the trick, or you have to take apart the buttons front and clean the contacts.

Moritz Bohlen -