Introducción
Actualiza una MacBook Pro envejecida con un nuevo par de pies.
-
-
Extrae los siguientes diez tornillos:
-
Tres tornillos Phillips #00 de 14.4 mm
-
Tres tornillos Phillips #00 de 3.5 mm
-
Cuatro tornillos de resalto Phillips #00 de 3.5 mm
-
-
-
Usa tus dedos a modo de palanca para levantar la tapa inferior del cuerpo del MacBook por la zona del ventilador.
-
Extrae la tapa inferior.
-
-
-
Retirar cualquier pie roto o dañado.
-
Retira cualquier pieza del pie viejo que se haya roto en el orificio para el pie.
-
Usa pinzas para despegar y quitar la cinta adhesiva vieja de la almohadilla del pie.
-
-
-
Frota la almohadilla del pie con un removedor de adhesivo para eliminar cualquier resto de adhesivo.
-
-
-
Limpia la almohadilla del pie con una almohadilla preparada con alcohol para eliminar cualquier residuo que haya dejado el limpiador.
-
-
-
Alinea el pie nuevo dentro de la almohadilla del pie.
-
Asegúrate de que la protuberancia de alineación del pie esté alineada con el pequeño orificio cerca del perímetro de la almohadilla.
-
Coloca el pie hacia abajo mientras lo mantienes correctamente alineado.
-
Verifica la alineación correcta desde el interior de la caja inferior. Usa pinzas para deslizar la protuberancia de alineación para que se alinee con el orificio.
-
-
-
Presiona el pie nuevo hacia abajo firmemente con el dedo y mantén la presión durante 30 segundos para fijar el adhesivo sensible a la presión. Apoya el otro lado de la cubierta mientras presionas el pie hacia abajo.
-
Repite los últimos seis pasos para cualquier pie roto o dañado.
-
Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.
How much weight can I save by removing the optical drive?
gunes314 -
You can save a lot of weight if lets say your installing a solid state drive or putting in a second hard drive but if you know that you use the CD/DVD disc drive a lot then you might just want to leave the drive alone.
Marshall WahlstromHelgren -
Tip: Use one of those weekday pill holders to have a cheep way to store screws you remove and each day of the week can be for different sizes or parts. It has been handy to have (much less expensive than the magnetic mat.
Robert Wacker -
Hello, where can I buy the screws I need in case I lose one of them?
taylornya -
iFixit sells a kit: MacBook Pro Unibody Lower Case Screw Set
Darrell Johnson -
I have one stripped screw... How opening without drill it?! Any suggestions please?
rodrigosady -
I also stripped a couple screws. I wasn’t able to open it up without drilling. After drilling the heads and removing the cover it was easy to hacksaw the tip and unscrew with a standard driver.
Michael Wilkens -
We have a guide for that!
Cómo quitar un tornillo barrido
Sam Omiotek -
My top tip - make sure you buy good quality Phillips screwdrivers and a magnetic holder. Cheap screwdrivers won’t get the screws undone safely. Without a magnetic holder you have no chance of getting the tiny crews in and out safely.
jeremyyoung -
A good Phillips 00 is your friend here. Also, when reinserting the screws, gently start anticlockwise and you wil feel a click at the start of the thread. This tells you you’re in the right place and less likely to cross-thread through force in the wrong place.
Iain Boyd -
I feel like these are 000 screws. Amazon sales describe them as such and my 000 screwdriver fits better
cam2000deluxe -
Before ordering a new Trackpad remove the existing battery and try clicking the Trackpad. If it clicks OK with the battery out the source of problem is likely a swollen battery, which should to be replaced even if it still works to some degree. From the side of the battery you will likely see the soft part of the battery bulging beyond the hard case.
Patrick Langvardt -
That’s absolutely correct as I can testify. With the battery removed I also adjusted the T6 set screw that adjusts the sensitivity of the trackpad click, evidently someone had cranked mine down tighter than the factory setting.
Gary Register -
Le quatrième paragraphe dans les instructions en français n’est pas correct : ce ne sont pas les 2 petites vis, mais les 7 petites vis qui sont inclinées. Et les 3 grandes sont bien verticales.
Degeorges -
Bonjour ! Merci de votre observation. J’ai corrigé la traduction. iFixit étant un wiki, n’hésitez pas à modifiez si vous remarquez une erreur :) Encore merci de votre attention et à bientôt !
Claire Miesch -
Tip: if you have a magnetic screw mat or similar, lay the macbook over the mat to make sure it catches any screws that may decide to fall of and hide under your table
Moritz -
Funny, it's not her hands that are doing the close ups. :)
Cinemated Man -
What's the difference between the shouldered and non shouldered screws? They look exactly the same to me.
MLNLRD -