Reemplazo del botón lateral derecho de PlayStation Vita

Escrito Por: Brittany McCrigler

Comentarios: 18

Reemplazo del botón lateral derecho de PlayStation Vita

Dificultad

Moderado

Pasos

Tiempo Requerido

20 - 30 minutos

Introducción

Esta guía te lleva a través del proceso de instalación del botón lateral derecho.

Herramientas

Partes

Paso 1

Apague y retire la tarjeta de memoria.
Usando un destornillador Phillips # 00, retire los cuatro tornillos de 6,4 mm en la carcasa trasera

Paso 2

Usando la uña o un spudger, abra la cubierta del puerto de accesorios en la parte superior del dispositivo.
Usando un destornillador Phillips # 00, retire los dos tornillos de 5.4mm ocultos debajo de la cubierta del puerto de accesorios.

Paso 3

Retire los dos tornillos Phillips # 00 de 5.4mm en la parte inferior del dispositivo cerca del puerto de carga.

Paso 4

Comenzando a los lados del dispositivo, utilice una herramienta de apertura de plástico para separar la carcasa delantera y trasera.
Continue deslizando la herramienta de apertura al rededor del borde.
Todavía hay alambres que mantiene juntas las carcasas delantera y trasera. Usted puede dañar las conexiones si separa las carcasas de forma brusca.

Paso 5

Suavemente separar las dos carcasas, teniendo en cuenta la batería y los conectores del controlador de pantalla táctil que mantienen las carcasas juntas..

One of the shoulder buttons fell out when I was doing this step, along with the piece holding it in place. They go back in just fine when reassembling but make sure that they are oriented properly, of course.

klung - 03/04/21

Paso 6

Utilizando un spudger, libere el cable flexible del controlador de la pantalla táctil suavemente levantando la conexión.

Paso 7

Libere el cable de la batería levantando suavemente la conexión con un spudger.

Any idea what type of pcb header is on the board for the battery? I have a motherboard with a broken header but I cant source a replacement

Jimbo Jones - 17/05/17

This is where I screwed up so I recommend extra caution for other newbies. Only the black part is supposed to come off. Don't be an idiot like me and pry off too much...

ylimakiminna - 22/06/17

Yea I messed up there too. Is there a way to fix it?

Alethia Henry - 08/08/17

This component was far more stubborn than the screen connector when it came to removal. I opted for a smaller tool than the spudger (small flat-head) and managed to disconnect it after determining the best bit size for the job. Screwdriver is metal, obviously, so being gentle helps to avoid damaging anything.

klung - 03/04/21

Paso 8

Separar las carcasas delantera y trasera.

Paso 9

Utilizando el extremo puntiagudo del spudger, desconecte los tres conectores del cable de la antena en la parte superior de la tarjeta inalámbrica.
Deruta los cables de la antena de modo que estén fuera de la carcasa de la tarjeta inalámbrica. Ponga los cables lejos.

Step 9-11 only apply to the 3G version of the PS Vita.

logicj83 - 03/01/15

Hello, I have the PCH-2001 model of the PS vita and the right analog stick went out. I ordered a replacement and the stick is slightly larger than the original. The original has a black rectangle on the back, the new version has the star version, which is what you have on this website as the replacement part. Any help here would be much appreciated. Thanks.

Ben Ragains - 17/06/15

Can I install a WiFi motherboard on a 3g ps vita model 1100?

fmind11 - 07/10/19

Paso 10

Enganche el spudger debajo de la lengüeta de la carcasa de la tarjeta inalámbrica y suelte la lengüeta.
Descubra y quite la carcasa de la tarjeta inalámbrica.

Paso 11

Retire los dos tornillos Phillips # 00 de 4.4mm de la tarjeta inalámbrica.
La tarjeta inalámbrica saldrá naturalmente hacia fuera en un ángulo.
Saque la tarjeta inalámbrica.

My screwdriver does not want to unscrew those. They won’t turn at all.

Rei - 04/10/18

My screwdriver does not want to unscrew those. They won’t turn at all.

Got the same, used PH #0 and grabbed wireless card casing with fingers from the top to release pressure on screen and avoid (possibly) breaking it.

Yuriy Zhyromskiy - 13/01/20

Some PS vita models seem to use a T2 screw instead of a PH#00. I’ve encountered this twice now.

kaosjr kaosjr - 23/03/21

I replaced de wifi card but is still difficult to connect to wifi. Could it be the wifi antenna? which cable model is it?

Fernando Diaz -

Paso 12

Levanta la carcasa del botón del hombro derecho con un spudger y déjalo a un lado.

Is this really necessary?

fmind11 - 09/10/19

Paso 13

Quita la cubierta de plástico translúcida del botón lateral derecho.

Paso 14

Suelta el enchufe del cable flexible del botón del hombro derecho usando un spudger para abrir suavemente la pestaña.
Con unas pinzas, desliza el cable flexible fuera del zócalo.

Paso 15

Usando un spudger, despega suavemente el botón lateral derecho del adhesivo ligero que lo conecta a la carcasa.

Conclusión

Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.

Autor

Brittany McCrigler

Miembro Desde 05/03/12

88184 Reputación

5 comentarios

Is anyone else experiencing the button getting stuck?

Fantasy Silicone Statuettes - 01/05/14

Yes, mine is getting stuck, too. I am hoping a replacement will solve this problem.

aseelau - 11/05/17

Has anyone experienced or seen an issue where the trigger button acts with the same functionality as the home button. Every time I press the right trigger it exits to home or exits the game.....help please

Daniel - 10/05/16

I followed this guide on my 3G vita in order to replace the right trigger cable. I found it wasn't necessary to remove the wireless card if anyone else finds that part tricky.

Caleb - 15/01/17

i am replacing the whole front part of my vita do to screen cracked and wont turn on, when i put the button back on, how would i do so to make it stick back on? would i need to reglue it or will it stick back on by itself?

Saul Calderon - 25/03/18