Reemplazo del conjunto de protección superior de la PlayStation 3 Slim

Escrito Por: Andrew Bookholt
  • Comentarios: 7
Reemplazo del conjunto de protección superior de la PlayStation 3 Slim

Dificultad

Difícil

Pasos

7

Tiempo Requerido

No hay estimado

Introducción

  1. EvRECjv6qHRK6tBR

    • Desconecta los cables de alimentación de entrada de CC y Blu-ray de la placa base.

    • Tira de los cables hacia arriba para levantar los conectores y sacarlos de sus zócalos en la placa base.

  2. DKCRxFDxdykYjIVB

    • Tira de los cables del ventilador hacia arriba para levantar el conector del ventilador y sacarlo de su zócalo en la placa base.

    You have to be very very careful on this step as the connector is very fragile. One wrong move and you can end up with a ripped off connector which wont be repairable.

    Source: Followed this guide and ripped off the connector from my PS3

    Jatinder Singh -

    I’ve broken the solder on the fan conn. Any help?

    Brian DiGiaimo -

    I think I can solder it

    Brian DiGiaimo -

    I have also ripped off the connector and only realized when I wanted to put together.

    Visegradi Istvan -

    ONLY FOR EXPERIENCED ELECTRICIANS!

    It is not impossible to clean the removed connector from the panel parts and then glue the connector back on the panel. It depends how much connection is left on the board (you might able to clean a bit of green carefully to increase connection size) with a bit of experience you can solder it back/together again. The power and ground needs better connection since it needs to able to carry the current. The RPM signal has the least connection size on this side of the board but it needs only a bit of connection.

    Other possibility to bring from the board other side the 3 fan connection points with some tiny cables but that is more labour intensive and you might need to cut a bit from the metal panel to make space of the cables.

    Anyway it is a doable job for an experienced repair person.

    Visegradi Istvan -

  3. 6NsUNbe6Dc3A6JPr

    • Retira los siguientes nueve tornillos que sujetan el ensamblaje de la placa base:

    • Cuatro Phillips con hombros de 14,8 mm

    • Cinco Phillips de 9,5 mm

    jesus chris what screw driver do i use for the 9.5mm phillips i cant find one anywhere

    Capsoul GotTheHits -

    The PH#1 screwdriver from iFixit's "Manta" driver bit set worked fine for me

    Nicholas -

  4. WYO5ZZydIoA3OasP

    • Retira las dos abrazaderas del disipador de calor de la parte inferior del ensamblaje de la placa base.

  5. sLwBLGSahXNOwUxv

    • Si es necesario, saca con cuidado la placa base del protector superior cerca del disipador de calor y su cubierta.

  6. JYevVfWoGFthVlDs
    JYevVfWoGFthVlDs
    4EOYDLPSpSbsTNl1

    • Presiona suavemente la placa para alejarla del ensamblaje del protector superior cerca del conector del ventilador y la esquina de la placa cerca de los enchufes inalámbricos.

  7. WhjuJRsbuIjtZGmc

    • Levanta el ensamblaje del protector superior de la placa base desde su borde frontal.

    • Ten cuidado de no dañar los zócalos al girar el conjunto del protector superior para alejarlo de la placa base.

Conclusión

Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.

Autor

Andrew Bookholt

578639 Reputación

0 comentarios