Reemplazo del ventilador para Mac Pro a finales de 2013

Escrito Por: Andrew Optimus Goldheart
  • Comentarios: 22
Reemplazo del ventilador para Mac Pro a finales de 2013

Dificultad

Moderado

Pasos

19

Tiempo Requerido

No hay estimado

Introducción

El Mac Pro se mantiene frío por un solo ventilador centrífugo. Utiliza esta guía para quitar el ventilador para limpiarlo o reemplazarlo.

  1. UvUDEeuAGOcSyZ6Y
    UvUDEeuAGOcSyZ6Y
    6E4dVROBn2KCRitH

    • Desliza el interruptor de bloqueo hacia la derecha, hasta la posición de desbloqueo.

  2. 1T6FWnrfHWRH2PIX
    1T6FWnrfHWRH2PIX
    LZUjZMT1W2HyocfY
    qEZURvNGfsFRhn15

    • Levanta la caja exterior directamente hacia arriba del Mac Pro.

    • Puede ayudar empujar hacia abajo el centro del ventilador mientras levanta la caja.

  3. thx2PRFESOcKGAcF
    thx2PRFESOcKGAcF
    fowEwJDQUHt5gRvN
    YkicYtjklAO35ERL

    • Quita los cinco tornillos Torx T10 de 5.1 mm de todo el perímetro exterior del ensamblaje del ventilador.

    You don't have to remove the fan assy to get to the wifi board & card. It can be done with the fan assy still attached.

    Fat Mango -

    Fat Mango is correct. That said. If you do pull the fan assembly note that the screws are all held in with blue Permatex and breaking them free takes a fair amount of effort. Getting a good set of Torx screwdrivers is a must.

    Jim WIlson -

    Hey guys, what would happen if you only replace one card.. I have a D300 but the plan is to upgrade to D500 or D600. So If I can afford and install one instead of the pair would it increase something? or will it cause any conflict? I guess I don’t understand if I the Mac Pro has 2 D300 graphic cards that means each has 1GB? Same as If I would Install 1 D600 that would increase 3GB only? Thanks.

    marcotamayo -

    D300 = 2GB each card. Very few apps uses two cards at the same time.

    Gio Cas -

    The (5) Screws are Apple part number 923-0713

    Steven Gier -

  4. fEANTTnYS4TS3pQD
    fEANTTnYS4TS3pQD
    V2ArmlpPcrPPbGTB

    • El ensamblaje del ventilador está conectado al resto de la computadora mediante dos cables en el lado de la placa de E/S.

    • Incline el ensamblaje hacia arriba alejándolo de la placa de E/S.

    • No intentes extraer el ensamblaje del ventilador todavía, ya que aún está conectado por dos cables.

  5. lceQ6InRYFH5qg2f

    • Mientras sostienes el ensamblaje del ventilador con una mano, afloja los dos tornillos cautivos T8 en el soporte del cable del ventilador.

    • Estos tornillos están atrapados en la Mac Pro. No intentes quitar estos tornillos de tu Mac Pro.

    On my Mac Pro (assembled mid-2017) these are T8 screws. In fact, there were no T7 screws anywhere in my machine.

    mark33 -

    There was no bracket on top of the cable at all, so I got a bit confused, so I had to skip step 5 and 6.

    Rakesh -

    On my machine, a TR7 worked to remove them due to the weird angle.

    Wilson Gaberino -

  6. Y6MKDVBUdIumVZuf

    • Usa un par de pinzas para tirar del soporte del cable del ventilador y alejarlo del ensamblaje del ventilador.

  7. JUE2RPF2GwjcP2kr
    JUE2RPF2GwjcP2kr
    oW6DugeJyYrgKGD4

    • Utiliza el extremo plano de un spudger para desconectar el cable plano del ensamblaje del ventilador de la placa de E/S.

  8. wMMmqDsn3NjCMRWu

    • Desconecte el cable de la antena del ensamblaje del ventilador de la placa E/S.

    • Retira el ensamblaje del ventilador del Mac Pro.

    You don't have to remove the fan assy to do the steps below. They can be done with the fan assy still attached.

    Fat Mango -

  9. apNLOQVTbSwRJEmE
    apNLOQVTbSwRJEmE
    rayTDFNEYXXyajCi
    lJfnXsGRmB1PhKgl

    • Usa el extremo plano de un spudger para levantar la tapa del ensamblaje del ventilador.

    • Remueve la tapa del ensamblaje del ventilador.

    There is a thin circle of double sided adhesive that must be loosened in order to remove the plastic cover.

    somethingorother -

  10. PGPYZIOrE1pyOwKd

    • Retira los tres tornillos T4 de 3.7 mm que sujetan la cubierta de metal al compartimiento de la placa AirPort.

    I had better luck using a T5 driver.

    somethingorother -

    Same here. Mine were T5, not T4.

    Carsten Clark -

    t4 was good for me

    Arden De Cuir -

  11. Y5vOw5AaByHX1PUG

    • Levanta y retire la cubierta metálica del compartimiento de la placa AirPort.

  12. HioOaQOGRla4SCVb
    HioOaQOGRla4SCVb
    C646tHfOke2DRgKx
    HjDt4JNgKyaleTSj

    • Usa la punta de un spudger para voltear la pestaña de retención ZIF en el conector del cable plano del ensamblaje del ventilador.

    • Retira el cable plano del ensamblaje del ventilador de su zócalo ZIF.

  13. CCqnEFchgYXuKXAu
    CCqnEFchgYXuKXAu
    rhe2NNlNTCGFyVW1
    mfwaOUY31M1hKxJV

    • Usa la punta de un spudger para voltear la lengüeta de retención ZIF en el cable plano del ventilador.

    • Desconecta el cable plano del ventilador.

  14. kqHqADw3Ejeg2me2

    • Retira los tres tornillos T4 de 3.7 mm que sujetan el bisel del ventilador al ensamblaje del ventilador.

  15. Jsg1taZGZFjNnrov
    Jsg1taZGZFjNnrov
    T1ERxVoCHMmSmRu2

    • Retira el bisel del ventilador.

  16. ZZ3Io1GVRrot1gX4

    • Retira los siguientes tornillos de la parte superior del ensamblaje del ventilador:

    • Un tornillo T10 de 10.4 mm.

    • Tres tornillos de 3.7 mm T4

    'T4' screws here VERY tight - iFixit T4 bit spun out on 2, but managed to get them to turn with T5 bit and firm downward pressure....

    vbob -

  17. pFnLjPUGCvFm2Mb6
    pFnLjPUGCvFm2Mb6
    LP26EkIPDTYCG5oZ

    • Da vuelta al tablero AirPort.

  18. BOi212riQI6LyGLO

    • Retira los dos tornillos T10 de 10.4 mm restantes que sujetan el ventilador al ensamblaje del ventilador.

  19. ITyrTSYDV2AWqtyH
    ITyrTSYDV2AWqtyH
    rl23ifXnxqgEIld4
    XEy3ga2Dj5atquQK

    • Levanta el ensamblaje del ventilador para arriba del ventilador.

    No way to install that last ribbon of a new fan is actually put on the last ribbon is attached

    themichaelguy -

    I would be happy to pay 100 dollars to find the solution for the last ribbon coennection when a new fan is actually put on

    themichaelguy -

    THANK YOU, now I know how to connect the ribbon to the fan again.

    Darius Zendeh -

Conclusión

Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.

Autor

Andrew Optimus Goldheart

Miembro Desde 17/10/09

494144 Reputación

5 comentarios

using my iFixit bit set, I'd have to say that the tiny screws for Airport card & cover, as well as fan bezel, are actually T5, not T4 - came very close to stripping the heads on two of the Airport card screws with the recommended T4 bit, but firm pressure and a steady hand with T5 bit got them out. Thanks for the guide - many careful steps to get a scrap of scotch tape out of the fan where its gentle ticks-ticka was driving us crazy thinking something far worse was going wrong.....

vbob -

Ha! I wondered what would happen if some tiny flotsam was dropped in through the top - terrible! Thanks for the tip!

Wagon Fixin -

Likewise, I've had a random noise in the fan at startup, and finally took the fan assembly apart to grab it. It was some even tinier screw from somewhere that had lodged in part of the fan housing. All is very, very well now!!!!

Colin Wright -

Hey Colin, I have same fan startup nois in my MP. Can you help me and tell how to fix in few steps?

Deny -

Using Macs Fan Control, I noticed the baseline fan speed of my “trashcan” slowly creeping up from 790 RPM (the usual) to 8 or 900 RPM. Using this guide I took the fan assembly off, and vacuumed and dusted everything with a vacuum, soft brush and canned air. It wasn’t necessary to disassemble the fan unit itself. That did the trick - fan speed is back down to 790 RPM after putting it back together.

PS - in Step 5, a Torx T8 screwdriver seemed to fit just fine for the fan cable bracket screws.

isonno -