Sustitución del Tubo de Calor de la PlayStation 4 Pro

Escrito Por: Thomas
  • Comentarios: 50
Sustitución del Tubo de Calor de la PlayStation 4 Pro

Dificultad

Moderado

Pasos

15

Tiempo Requerido

20 - 30 minutos

Introducción

Esta guía mostrará los pasos necesarios para reemplazar el tubo de calor en la PS4 Pro. Este proceso implica el desmontaje que anula la garantía y muchos pasos. El tubo de calor está ubicado a medio camino entre la parte superior e inferior de la PS4 Pro y, por lo tanto, requiere que se retiren los componentes de ambos lados para reemplazarlo.

  1. 54rT6gxKYMdDALg2
    54rT6gxKYMdDALg2
    NMFNlBRXta42yJSx
    AJvelILqtOoEZyPh

    • Voltear la consola al revés.

    • Utilice su dedo para tirar y quitar la tapa de plástico sobre el disco duro.

    DON’T FORGET TO HAVE THERMAL PASTE HANDY! It should be added to the “Tools Required” Section. You will NEED it!

    Jaquell Chandler -

    What if thermal paste is not applied again when remounting ? Will the playstation start and work anyway or not ?

    Vincent Bee -

    It will start and run normally until you put it under load. Then it will heat up and thermal throttle or it can overheat and destroy itself.

    Jeremy Ivey -

    I posted this down in another step too, but: if you have a very early North American PS4 Pro, with the exact optical drive shown here - the key way to tell is the very long data cable that’s folded a couple of times, see pictures in later steps - then the replacement drive iFixit offers WILL NOT WORK IN YOUR MACHINE. It has to be a very early model, apparently, but the model number isn’t enough to tell you.

    Even if you swap the too-short cables in their replacement with the longer cables on your drive, it still will not work. At all. It’ll just sit there like the drive isn’t even getting power.

    So if you do have this drive, what you probably need to do is get a replacement KES-496A Optical Pickup Assembly and replace that within your existing drive. That’s what I had to do after two different replacement drives sent by iFixit failed to work in my system. It worked immediately and I’m back online.

    The optical pickup replacement is awfully fiddly, and adds a solid 20 minutes to the repair easily. But it does work.

    Dara Korra'ti -

  2. RR6LZcIKB6LHbgHD
    RR6LZcIKB6LHbgHD
    SDci2Vv2GAmVwWXk

    • Utilice un destornillador Phillips # 0 para quitar el tornillo único que asegura la jaula de la unidad de disco duro.

    • Tire de la jaula de la unidad de disco duro hacia afuera.

    This is a Phillips #1 bit.

    Trevor Frey -

  3. TEfsVkAhghmOwoLV
    TEfsVkAhghmOwoLV
    5kWOpQHUOUHPFx3o
    kBmwtXcnRhNAWAa4

    • Voltea la consola hacia arriba.

    • Aprieta los dos laterales en el frontal del equipo.

    • Tirar hacia arriba hasta escuchar un fuerte Click.

    • Esto requiere un poco de fuerza, así que no tengas miedo de ser un poco bruto con tu consola.

    • Despues de separar los laterales, desliza la tapa hacia atrás y sepárala.

    %#*@. I thought I was gonna break the thing. You really do have to give it some elbow grease.

    Addison Francisco -

    there were also some screws that needed to come out before popping it off. Might have been a different version im working on. there were three screws attached to the console that I had to remove before popping off the top.

    Ricky Arias -

    The 7215B has one TR8 security Torx behind the center “void” sticker.

    cylentstorm -

    This cover is really on there. It sounds like your breaking plastic when you pop it open. I ended up using a metal tablespoon in the corners where you should pull up to pop the cover up the first bit, worked well.

    azade91 -

  4. 22wpYKO4yTNgW3Kh
    22wpYKO4yTNgW3Kh
    vBx4W1iSIAwRpNoD
    jOxTLN2D2HYZVHRG

    • Utilice un destornillador de seguridad Torx T8 para quitar los cinco tornillos de la parte posterior del dispositivo.

    • Dos tornillos de 31mm.

    • Tres tornillos de 10 mm para los modelos 7000; dos tornillos grises de 10 mm (superior e inferior en la ilustración) si la PS4 Pro es un modelo de la serie 7100.

    • Retire la placa de metal tirando de ella.

    I copy the comment written by Jason at the end of this guide, because it’s better to have it here:

    This guide is for the initial release CUH-7000 models. Of note is the changes to the CUH-7100 series that do make this guide an issue. Steps 4 and 5 have a different items to note. You can damage it following this guide if you don’t adjust. There no longer 3 security screws for the case, but just one. This single screw is still covered by a warranty sticker, but the second one is a blank sticker and no screw behind it. There is also no 10mm screw in the center power supply in Step 4, it’s a support post. You still remove the 4 other screws, but you must then flip the console over and remove a T8 screw to the right on the HDD cage and another closer to the right side. You can then flip the console over again to remove the battery and plug it. Just remove all the metal plate screws to be sure, but make sure you hold the board when you flip it again or you will bend the battery prongs like I found out the hard way.

    kautame -

    Oh! That explains why I stripped the middle screw. What’s a support post?

    Philippe Morin -

    Had to use TR8 instead of 10mm here.

    Addison Francisco -

    After I popped the top off, I got 4 out of 5 screws out. The 5 th screw for some reason, was a little bit bigger, therefore, I could not take out that screw so I could clean the heatsink and fan.

    Dixie Dawg -

    Me too it’s not like another screw it’s have black and I can’t remove if you know pls tell me how i do bro ???

    Montri Meka -

    I stripped the %#*@ screw in the middle. (orange highlighting) It’s a black head and the T8 Torx Security head doesn’t work! I have a CUH-7115B. I think it’s a regular T8 or some kind of Hex head. ? I don’t know what to do now!! :(

    Philippe Morin -

    As mentioned above, this guide is for the old models. 7215B: There 4 TR8 screws (2 long, 2 short) holding the plate. The middle is a support post.

    cylentstorm -

  5. JJlhIcb3U2yBLvMW
    JJlhIcb3U2yBLvMW
    DCfbqKLZUNXSO6Wh
    uMkvUSRNKvYVRAkZ

    • Mueve la consola hacia arriba para que la parte inferior quede hacia arriba.

    • Utiliza un destornillador de seguridad Torx T8 para retirar los tres tornillos negros de 7 mm del panel trasero. (sólo modelos de la serie 7000); o un tornillo de 7 mm (el del medio) con los modelos de la serie 7100 y la pegatina de garantía a la izquierda.

    • Retira la cubierta inferior de la misma manera que la cubierta superior. Agarra la cubierta por ambos lados y tire hacia arriba hasta que haga clic. A continuación, desliza la cubierta hacia fuera; En los modelos de la serie 7100, presta atención a los dos clips que sustituyen a los tornillos correspondientes.

    Adding to this, the screws are not visible unless you remove the warranty stickers!

    George Diaz -

    Also, the plastic on the back of the cover is prone to cracking. Be careful and undo snaps across the whole back of the panel gently!

    Nick Podrebarac -

    Vielen vielen Dank. Endlich ist der jumbojet gelandet #fan

    Christian Radke -

    7215B has 1 TR8 screw beneath a sticker between the optical and USB ports, and two clips (1 next to the HDD slot and 1 beneath a sticker near the power port.)

    cylentstorm -

  6. XVJsyqaqvWMpHyML
    XVJsyqaqvWMpHyML
    qYeNPcGxS3SLHqCt
    YSgOJyhZRcqRxp4A

    • Utiliza un destornillador de seguridad Torx T8 para retirar los once tornillos plateados de 10 mm de la placa metálica.

    • Utiliza un destornillador Phillips nº 1 para retirar los once tornillos negros de 4 mm de la placa metálica.

    • Los modelos de la serie 7200 tienen 13 tornillos adicionales de 4 mm alrededor de la parte superior y derecha de la placa metálica. Estos tornillos están indicados con un triángulo. Esto puede aplicarse a otros modelos.

    • Desconecta los tres cables de la antena (dos negros y uno blanco) haciendo palanca para sacarlos de sus zócalos.

    Noted during my replacement that the PS4 Pro appears to have additional #0 Phillips Head screws in Step 6 required to remove the metal plate from the motherboard and that the metal “X” plate in Step 11 appears to be included now in this overall metal cover for the motherboard, no longer separate, which accounts for the additional screws.

    David Carlsen -

    Original pro here. Had 12 torx

    Skyler Cook -

    cuh0-7216b have more philips #1 screws on metal plate on right, +13 screws :)

    Papolo0 -

    (PS4 Pro) Bei mir ebenfalls 11 T8 Torx, von denen 3 Sicherheitstorx waren.

    Rebecca Dorsch -

    My PS4 Pro 7115 has additional sets of #0 Phillips screws on the plate. 10x in the primary processor space (blank plate area of the graphic here), 2x over the fan, and 1x on the outside edge to clamp down on the primary processor area. Model CUH-7115B

    r0flm4k3r -

  7. heEDQBHHh5KdEDR6
    heEDQBHHh5KdEDR6
    rZU2aMJngJnkmHDS

    • Tire del conector blanco directamente del soporte amarillo de la placa base.

  8. FDTBl1FGfJFeSuA1
    FDTBl1FGfJFeSuA1
    ym5X6LUCOKJEJM36

    • Saque los cinco pequeños cables de perfil bajo azul conectados a la placa de metal.

    • Levante la solapa de retención del conector ZIF del cable de cinta grande.

    • Tirar del cable de cinta ancha de su zócalo.

    • No tire del cable azul grande sin levantar la pestaña en primer lugar. Si lo hace, puede dañar la conexión.

    What the cable in the up left corner is for? I broke it and i’d like to know at what is it connected?

    Thanks

    Enrico Pensalfine -

    The blue ribbon cables aren’t connected to the metal plate. The plate can be safely removed beforehand. The only thing one should do prior to its removal is de route the antenna cables for the WNIC.

    Robert -

  9. PoXEHXeCsNy6UAcG

    • Tire hacia arriba y retire la placa de metal.

  10. iNt5ZNLVFmWnNB2T
    iNt5ZNLVFmWnNB2T
    3Wj6Xx1YmrTOaDIg
    yCUNXe2bCxwEjKui

    • Vuelva a girar la consola para continuar trabajando en la parte superior.

    • Tire de la unidad de alimentación y colóquela en la consola.

    • Tenga cuidado de no tirar demasiado, el conjunto está todavía conectado en un punto.

    • Sujete el conector detrás de la fuente de alimentación y tire hacia afuera.

    Why do I have to remove the PSU here? I do not see the necessity judging by the following steps.

    Alexander Bla -

    This comes in handy when removing the entire motherboard which is necessary when cleaning the heat sink.

    George Diaz -

    Bonjour, Que se soit le connecteur du bloc comme celui sur la partie ps4 , il est difficile à retirer ce câblage… peut-on tirer sans risque réellement ?

    Brezu Sama -

    IMPORTANT: The connector on the motherboard is very sensitive. I’d recommend using pliers to put pressure down on the connector while slowly jerking the cable out of the socket to avoid serious damage to the connector and/or motherboard that could render the PSU connection useless and require advanced soldering / rewiring.

    Daniel Larusso -

    This!

    Connector was quite tight in PSU side and I ended pulling connector from motherboard resulting me getting PS5 for Christmas.

    tero -

    Also der stecke lässt sich nicht entfernen

    Slime -

    Der Stecker am Netzteil (letzter Schritt) erscheint mir ungewöhnlich fest, und lässt sich ohne weiteres nicht entfernen. Besteht die Möglichkeit, dass dieser neuerdings verklebt ist oder dergleichen? :-/

    Rebecca Dorsch -

    Das würde mich auch interessieren. Ich habe den Stecker weder vom Mainboartd noch von der PSU abbekommen. Leider habe ich den Stecker dann abgerissen - aber er hat sich auf keiner Seite abziehen lassen.

    Tobias August -

  11. 2FMFLlJQLrOsELKH
    2FMFLlJQLrOsELKH
    suV6EOjHNsSGf1HF
    VwP3K12dwEXXEGNJ

    • Voltea con cuidado la consola hacia arriba.

    • Usa el destornillador Phillips #1 para retirar los tornillos octogonales de 4mm en la plancha de metal con el símbolo X-like.

    • Usa una herramienta de plástico para remover la placa metálica con el símbolo de X-like.

    My PS4 Pro 7115, this and more is integrated with the main plate, as noted above, plus there are 10 in this area (not 8), along with 2 over the fan and 1 to the edge of this area. Model CUH-7115B

    r0flm4k3r -

  12. eOhijjfUUNjao5bC
    eOhijjfUUNjao5bC
    nDAmFP5RWvIA3YyY
    DlYWlbNmH4lAXlJ1

    • Usa un destornillador Phillips #1 para quitar los 4 tornillos de 13mm en la parte posterior de la placa de metal con forma de X.

    • Insertar traducción aquí

    Mine had an S shape with two screws.

    Christopher -

    Depending on the series it will have either a S or X shape bracket

    Jeremy Ivey -

    My PS4 Pro 7115 has an S-shaped bracket with 2 screws. Model CUH-7115B

    r0flm4k3r -

  13. ZVGLcoWfEpP6uPYN
    ZVGLcoWfEpP6uPYN
    g223aIoRByuQqbJn

    • Agarra el borde de la placa base y levántela lentamente hacia arriba para extraerla del dispositivo.

    • Para el remontaje, utiliza esta guía para volver a aplicar pasta térmica entre la placa base y la placa metálica situada debajo.

    Does anybody know the name of the white detail from the first screenshot step #13? (Plastic with square metal inside). I broke it by accident during dissembling and want to find replacement for it, but can’t find it anywhere.

    serjgord -

    I can read F2-4 >POM< on the plastic piece but i guess thisis a radiator/thermal dissipator support. HTH

    Vincent Bee -

    Won't you also need a paired optical drive to replace the motherboard? My ps4 got broken some weeks ago and I've found out that I need to replace the motherboard for it to work again, but I keep seeing that you also need a paired optical drive. Is this true? My ps4 pro is a CUH-7216B if that helps

    Jekabs Freimanis -

    A warning should be before this step that this step detaches from the primary heat sync. The required tools should list the replacement thermal paste at the beginning, not after the step is already to have been completed.

    r0flm4k3r -

    tut euch selbst den gefallen und tauscht auch alle Wärmeleitpads. (ca 14 stück)

    Jim Bean -

  14. kst6Ck1IX2mPuuCH
    kst6Ck1IX2mPuuCH
    AKlJDNeAiE5LZlg1

    • Usa un destornillador Phillips #0 para quitar los dos tornillos plateados de 6 mm de la placa de metal.

    Where to get the pink stuff from?

    Dark Flo -

    #1 Philips screwdriver

    Peter -

  15. fPhNCLSnvNnVFFaT
    fPhNCLSnvNnVFFaT
    XGDKImOJLJHRywXG

    • Levanta la placa de metal que está conectada a la tubería de calor hacia arriba para quitarla.

    The second screw is at the right bottom side !!

    mobilas77 -

Conclusión

Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.

Autor

Thomas

Miembro Desde 26/04/17

3573 Reputación

3 comentarios

Ist es schlimm, wenn man die 2 schrauben von schritt 14 vergessen hat zum verschrauben?

AxoN z -

Can anyone explain what are those 5 blocks near heatsink as mine are broken when I open it 2 blocks have converted into dust plz help

rajatagg41 -

This guide doesn't tell how to change the Heat Pipe on the later models. In my 72xx version, the Heat Pipe can be seperated from the chassis plating with 4 screws (ph#1)

TdG -